Windows 10: After Reset computer does not boot

Hi I have the following Problem:

I reset my computer because of some technical issues I was having. After the reset finished I wanted to reinstall windows. But after the Hi there lets get some information screen (country, language...) the computer runs into problem. It goes to the one moment page and then stays there for several minutes. After that the Laptop just shuts down and restarts telling me there was a problem. It does this every time I try to install windows. My Laptop is Plugged in and connected to WIFI. I have a dell Inspiration Laptop. Any help is appreciated.

:)

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

 

Unable to boot the computer.

Hi Samid,

Thank you for posting your query on Microsoft Community.

Before we proceed, we would require more information to assist you further.

• 
  What is the make and model of your computer?
  

I suggest you check if you are able to boot into Windows Recovery Environment using installation media. Follow the steps provided below and check.

• • Insert the installation USB and boot Windows 10 from it.
  • In the ‘Windows setup’ page select the ‘language to install’, ‘Time and currency format’ and the ‘keyboard or input method’ and click on ‘next’.
  • Click on ‘Repair your computer’ and select ‘Troubleshoot’.

Check if you are able to boot to this window. If you are unable to boot to this window, I suggest you to contact the manufacturer and check.

Hope this information is helpful. Reply us with this information to assist you further.

Thank you.

 

Computer keeps re-booting

Hi,

Thank you for your interest in Windows 10.

I suggest you to follow the methods below and check if it helps.

Method 1

Disconnect all the external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except mouse and the keyboard and then check.

Method 2

I suggest you to run in-built Power troubleshooter and check. Follow the steps:

• Press Windows Key + X.
• Click on Control Panel.
• Select Troubleshooting on the left pane, click on
  View All.
• Click on Power to run the troubleshooter.

Method 3

If the above method doesn’t help, I suggest you to reset and restore all of the default Power Plans back to their default settings. Follow the steps:

• Press Windows Key + X.
• Select Command Prompt (Admin).
• At the command prompt, type powercfg -restoredefaultschemes, and then press
  ENTER.
• At the command prompt, type exit to exit the Command Prompt window.
• Restart the computer and check with the issue.

Method 4: Clean boot

Putting your system in Clean Boot state helps in identifying if any third party applications or startup items are causing the issue. You need to follow the steps from the article mentioned below to perform a Clean Boot:

http://support.microsoft.com/kb/929135/en-us

Note: After clean boot troubleshooting steps, refer to the section "How to reset the computer to start as usual after troubleshooting with clean boot" in the provided link to return your computer
to Normal startup mode.

Hope this information is helpful. Please do let us know if you need further assistance, we’ll be glad to assist you.