Windows 10: impossible to find the file.....& error 0x80070002

I hope this is the correct side for the following thread.

Product: HP PRODESK 400G4MT
Operating System: Microsoft Windows 10 (64-Bit)

Since one week the installation of new applications stops with message: " impossible to find the file...."and sometimes with the issue: "error code 0x80070002".

Really the file exists on the computer system, but it is not anymore accessible.

Some applications, that where correctly operating, now are blocked with issues like " the file does not exist
(and error 1075 because the relevant service is freeze and impossible to modify).

I used MALWAREBYTES to find possible virus after put them in quarantine no improvement!
I also used Ccleaner to clean registers without result.

I scanned the system with sfc/scannow and the result was ok.

The issue "USERINIT" of HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon seems to be correct: C:\Windows\system32\userinit.exe,c:\Program Files (x86)\HP\HP ProtectTools Security Manager\Bin\DPAgent.exe,

I loaded a restore point of one mont before without results.
If I would repair the W10 I don't know if is possible to do without cancel the installed appliations.

Please I need suggestions: as last hope I would not reinitialize the computer since I have to reinstall all the applications...

Thanks

:)

 

.NET Framework 3.5 doesn't install. Error code 0x80070002 'The system cannot find the file specified' Windows 10 TP

Hi,

Thank you for posting your question on Microsoft Community.

As per the description I understand that you are unable to install
.NET Framework 3.5 and you are receiving the error 0x80070002.We regret for the inconvenience caused.

• Did you make any changes to the computer prior to the issue?

I would suggest you to try the steps from the following link:

Net Framework 3.5 and 4.5 error 0x80070002

Net Framework 3.5 and 4.5 error 0x80070002

Please let us know if you need further assistance.

Thank you.

 

Error Code 0x80070002 Refers To Windows 7

Hi,

Thank you for posting your query on Microsoft Community.

As per the issue description you are getting error code 0x80070002 while performing backup on your computer. I would suggest you to refer the suggestion provided in the article mentioned below. Though this article is for Windows 7 but steps holds good for
Windows 10 too.

Error code 0x8100002F and or error code 0x80070002 when you back up files in Windows 7


Hope this would help. If issue still persists post back with current status of your computer and result of the proposed suggestion, we will be happy to assist you.



Regards,

 

Windows Defender (SCEP 2012) when clicked on Update defenitions throws 0x80070002 error

Hi,

The error code 0x80070002 means that there are update files are incomplete or corrupted. We would like to ask for additional information. Please provide the following:

• Which build of Windows 10 are you using? To know about it, hit
  Start, type Winver and then press
  Enter. You could also press Windows Key + R, type
  Winver into the
  Run dialog and press Enter.
• Aside from trying to update the device, were there any changes made on the computer prior to the issue?
• Can you tell us what troubleshooting steps have you done so far?

Furthermore, we suggest that you check this article and follow the on-screen instructions. There are lists of troubleshooting
steps provided for each selection that you may follow. This applies on some common
error codes, such as: 0x80073712, 0x800705B4, 0x80004005, 0x8024402F, 0x80070002, 0x80070643, 0x80070003, 0x8024200B, 0x80070422, 0x80070020.

Looking forward to the requested information and the results of the recommended troubleshooting steps.