Windows 10: After having a "SYSTEM_THREAD_EXCEPTION_NOT_HANDLED" error my Laptop booted into an empty...

A few days ago I factory reset my laptop. I had some issues during this. When factory resetting it stopped after 22% and then it went to the login screen. When I tried to log in again however i got an error saying "user profile service failed the sign-in". However after trying various things, using the included ASUS troubleshooter and factory resetting my pc instead of using windows options by using the asus options, I got my clean PC. All well and good I thought.However, after 2 days of using my laptop, I got a blue screen of death and an "SYSTEM_THREAD_EXCEPTION_NOT_HANDLED" error message I

:)

 

SYSTEM_THREAD_EXCEPTION_NOT_HANDLED boot loop.


The usual causes for the system_thread_exception_not_handled crash are

• Insufficient disk space,
• Device driver,
• Video card,
• BIOS,
• Hardware incompatibility,
• Faulty system service,
• Memory,
• 3rd party remote control

I have removed 1, because it is not valid for this.

What I would like to try is to boot into safe mode via the command prompt in the advanced troubleshooting options, you need to open msconfig via the command
Code:

Code:

start msconfig

and from there go to the boot tab to enable safe mode.
This is a simple workaround for safe mode, but it usually works

If this works, then we can almost for sure assume a system service or driver is causing the problem.

 

laptop doesnt boot automatically

This is what happened.

1. Did a repair install and later disabled hibertnate in CMD.
2. Enabled legacy option ROM in BIOS.
3. After a few times startup ( i used the system in such mode for 5 days), changed boot option back to default.
4. Vola!! It boots automatically to win10 without any keypress. Tested it with many starts to confirm the same.
5. Re-enabled hibernate option using CMD and later selected Fast Startup.
6. System booted normally, without the need for any keypress.

I do not know exactly whether such steps resolved the problem or what else happened, hence cannot suggest above steps.

Many thanks to all members who helped to troubleshoot problems.

 

Error: "SYSTEM_THREAD_EXCEPTION_NOT_HANDLED." and unable to boot the device running Windows 10

Hi Dito,

As you are unable to access the operating system with SYSTEM_THREAD_EXCEPTION_NOT_HANDLED error, do not worry we will help you with this issue.

System Thread Exception Not Handled error in Windows 10 mostly arises due to incompatible or old
graphics card drivers. System Thread Exception Not Handled error is often displayed along with the Blue Screen of Death (BSOD).

As you are unable to boot the device from recovery tool, try the below and check if it helps.

I suggest you to create an installation media tool for Windows 10, change the boot order to boot from the CD/DVD or USB drive and perform an startup repair and check if it helps.

Step 1: I suggest you to create an installation media for
Windows 10 using the media creation tool:

Installing Windows 10 using the media creation tool

Step 2: Try to change the boot order.

Follow the below steps:

• Refer to the device user manual to know the key to enter in to
  Windows Recovery Environment.
• I suggest you to insert the DVD drive, hard restart the computer, and press the key (F2
  for DELL users), once the computer manufacturer logo pops-up.
• Change the Boot sequence to DVD/ USB drive
  under UEFI firmware settings and Restart. (Sequence depends on which external device you are using to boot the device)
• After your PC restarts, select the boot order and change accordingly by following the information available on the BIOS screen.

BIOS Disclaimer:

Modifying BIOS/ complementary metal oxide semiconductor (CMOS) settings incorrectly can cause serious problems that may prevent your computer from booting properly. Microsoft cannot guarantee that any problems resulting from the configuring of BIOS/CMOS settings
can be solved. Modifications of the settings are at your own risk.

After creating the tool perform Startup Repair.

Step 3: After creating installation media and changing the boot order try to perform Startup repair.

I would like to inform that, if your Windows 10 is not able to boot or startup, Startup Repair will come into action and try to diagnose and fix the issue. It will scan system files, registry settings, configuration settings and
more and try to fix the problem on its own, automatically.

Perform the Startup Repair:

• When your computer starts, wait for the manufacturer logo to check the option for boot menu, it will usually be
  F12.
• The boot menu key might differ with each manufacturer. If you are unable to find the boot menu key, you may refer the user manual.
• Restart the computer, when the manufacturer's logo is displayed, keep pressing the
  Boot menu option key to enter the boot menu and change the boot option to
  CD\DVD ROM.
• After you boot your computer using Windows 10 DVD, a black screen appears with gray text "Press any key to boot from CD or DVD". Press any key.
• Select the correct time and Keyboard type.
• Click Repair your computer in the lower left corner
• Click on Troubleshooting, advanced option and then click
  Startup Repair.

Hope it helps. Reply to the post for further assistance on this issue, we will be happy to help you.

Thank you.