Windows 10: Blue screen boot loop, can't access advanced startup options or boot from USB

Hello,


A vew days ago I ran into some blue screens when closing my windows 10 laptop. The third time this happend my laptop went into a boot loop. Which end with different blue screen error messages. So far i have seen:


DRIVER UNLOADED WITHOUT CANCELLING PENDING OPERATIONS

What failed: SynTP.sys

This is the one I get to see the most


ATTEMPTED WRITE TO READONLY MEMORY

What failed: SynTP.sys


KERNEL SECURITY CHECK FAILURE


PAGE FAULT IN NON PAGED AREA

What failed: IntcDAut.sys



In the beginning I was able to enter the windows advanced boot options and I tried to start in safe mode and run startup repair. Both did nothing to help the problem.


After diciding that a clean install of windows might help, I could no longer access the advanced boot options. After rebooting my laptop 3 times, which used to do the trick, I just get another blue screen eventhough it does say "preparing automatic repair".


I also tried reinstallig windows with a USB flash drive but I keep getting the blue screen directly after the first loading screen.


Any idea idea how I could fix this?

:)

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.

 

Booting from USB on x38 Motherboard, NOT?

See sys specs... ASUS ROG x38 motherboard, flashed to x48 Rampage.

In BIOS under "Boot Device Priority", I select and of the 3 boot device slots, and no where do I find an option for USB, these are the only options in each:

• 1st floopy drive
• HDD: P0-WDC WD2500KS
• ATAPI CD-ROM
• Disabled

Is there a place in the BIOS to enable boot from USB?

It's AMI, says v02.61 on the BIOS screen

 

Windows 10: Blue Screen on a Loop

Hi Lawrence, thanks for your reply.

Unfortunately I can't do what you suggested: booting process halts at the blue screen and Windows keeps restarting in a loop. I can't access my desktop.

All I can access is the troubleshooting menu that comes up automatically after PC has restarted a couple times in a row. I also have a bootable USB drive.

Is there any way I can fix errors and updates from command prompt in advanced troubleshooting options?

Thanks again