Windows 10: Blue Screen Loop - Cannot boot from USB

My PC, which is a custom built PC I've used for almost 2 years, has been stuck in a bluescreen loop. The only option I get at startup us going into bios or choosing boot drive. Windows bootable usb gives me a blue screen as well. Basically, I cannot do anything at startup aside from entering bios and choosing boot drive. The error message I get from bluescreen varies almost every time, I'm putting down the list of error messages below.

• System service exception
• 0xc000021a
• System thread exception not handled what failed: Ntfs.sys
• 0xc000007b
• IRQL not less or equal
• Page fault in nonpaged area
• Unexpected kernel mode trap
• Kernel data inpage error
• Critical service failed
• Kernel security page failed
• PFN list corrupt ... and probably many other

I had this same issue about 5 days ago, the same blue screen loop but occasionally I was able to enter advanced settings where it give me the menu of startup repair, system restore, uninstall recent updates, ect. All of which did not work. As the last resort, I booted form my bootable usb from advanced settings and clean installed windows 10. PC worked fine for 2 days but now I'm back to bluescreen loop. But this time it does not gives me the chance to enter advanced settings, just a blue screen loop. Please let me know if you have any suggestion. I'm thinking trying new CPU is my next option.

PC spec:

• CPU: Intel Core i7-8700 3.2 GHz 6-Core Processor
• Motherboard: MSI MPG Z390 GAMING PRO CARBON ATX LGA1151 Motherboard
• Storage: Samsung 860 Evo 1 TB 2.5" Solid State Drive
• RAM: Corsair Vengeance LPX 16 GB 2 x 8 GB DDR4-3200 CL16 Memory
• Power: EVGA G3 750 W 80+ Gold Certified Fully Modular ATX Power Supply
• OS: Windows 10 64bit

Other things I tried so far:

• Reset bios, update bios to most recent version
• new motherboard
• new ssd while unplugging the drives that were in use before
• boot without graphics card
• new sets of ram, in the right slot

:)

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.

 

Blue screen in terminal loop

Hi,

The blue screen error that you encounter can be triggered due to a possible hardware or hardware driver software failure. To isolate your concern, could you confirm if you have made any changes on your device prior to your concern? Also, are you getting
any messages for the blue screen error?

As an initial step to get out of the blue screen loop, we suggest that you perform a startup repair by booting to
System Recovery Options through a hard reboot. To do this, follow these steps:

• Turn on your device.
• When the Windows logo appears, press the power off button or unplug the power source to force shutdown your device.
  (If you're using a laptop, remove the battery. Note: Refer to the manufacturer's site on how to remove the battery of your device.)
• Perform this step three times. On the third time that you turn on your computer, wait for the
  Windows Recovery Environment (WinRE) window to appear.
• On the Choose an option screen, select Troubleshoot
  >Advanced options > Automatic Repair.
• Select Windows 10.
• If prompted, select an administrator account.
• Type in your password and click Continue.
• Wait for the repair to complete.

Once you're done, check if your device will boot normally.

We'll appreciate if you can send us an update.

 

Windows 10 Blue Screen Of Death Loop

Hi,

Blue screen errors are usually caused by outdated graphics drivers or system performances that can't be handled by it. We'd like to know more information about this issue so we could provide an accurate resolution. Kindly answer the following:

• Have you made any changes to your computer prior to this issue?
• Have you tried booting your PC in safe mode? You can refer to this article for the steps on how to boot
  your PC in safe mode.

In the meantime, we suggest that you go to this link and follow the steps to
Troubleshoot blue screen errors.

We'll be waiting for your response.