Windows 10: Bluescreen error and system crashes,

The computer has rebooted from a bugcheck. The bugcheck was: 0x00000133 0x0000000000000001, 0x0000000000001e00, 0xfffff8010f31c340, 0x0000000000000000. A dump was saved in: C:\WINDOWS\MEMORY.DMP. Report Id: 58a12555-8fda-4fd3-85c7-a68824b73833.event id is 1001

:)

 

Bluescreen Crashes in Windows 10

There are a few things that I notice with these errors, they are nearly all hardware 0x124 errors which are difficult to troubleshoot because there is so little information.

Most of them occur when the Norton Security process is running so a first step would be to uninstall Norton and just use Windows Defender while we are troubleshooting.

There was one different BSOD error: 0x18 Reference by Pointer
Probably caused by : BHDrvx64.sys ( BHDrvx64+114761 )

You need to update or rollback your Symantec Heuristics Driver. Maybe this is part of the Norton install so it may be removed anyway.

Check if there has been any improvement and if not then you will need to work through your hardware:



STOP 0x124 Troubleshooting [/i] Read carefully before proceeding.



Warning

If you're overclocking your system, revert back to stock clocks now.





Note Test the system once the overclock is removed before continuing with the steps outlined below.

Part One: CPU Stress Test
Part Two: MemTest86+ RAM Diagnostic
Part Three: Hard Drive Diagnostics
Part Four: GPU Stress Test




ONE [/i] CPU TEST
*Arrow Run Prime95 to stress test your CPU. Prime95 - Stress Test Your CPU - Windows 10 Forums



Warning Your CPU temperatures will rise quickly while under this stress test. Keep a keen eye on them and abort the test if overheating occurs.




TWO [/i] RAM TEST
*Arrow Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 10 Forums



Note



MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.




THREE [/i] HDD TEST


Note Please run HDTune first, in the order posted!
*Arrow Run HDTune to

• check the health,
• scan for errors, no quick scan but full scan
• run a benchmark.

It may take some time, but please take the time you need to perform it properly.
When above is done please make screenshots of the following

• the health,
• the error scan,
• the benchmark incl. following
  • transfer rate,
  • access time,
  • burst rate,
  • cpu usage.

*Arrow Run chkdsk




FOUR [/i] GPU TEST
*Arrow Run Furmark to stress test your GPU. FurMark - GPU Stress Test - Windows 10 Forums



Note Run Furmark for around 30 minutes.


Warning Your GPU temperatures will rise quickly while Furmark is running. Keep a keen eye on them and abort the test if overheating occurs.


Report back on all the tests as you do them - take your time - there is no need to get them all done immediately.

 

all games crash!

I suggest you run rthdribl > http://www.daionet.gr.jp/~masa/archives/rthdribl_1_2.zip
Increase the window size step by step and watch your vga temps permanently.
What happens?
If it crashes, run at stock speeds as suggested before and retry.

P.S.: When your system locks, does the display signal turn off after a time?
Stuttering sound or no sound at all when freezing?
What X1800XT model do you own exactly?

 

Windows 10 crashes in Startup and Autorepair. With Bluescreen Errorcode SYSTEM_THREAD_EXCEPTION_NOT_HANDLED

I was just shutdown PC and is crashed with this Bluescreen Error Code: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED. Then is restarting and crashes with the same Bluescreen Error Code. After 5 times Bluescreen, Automatic Repair. Well you will thinking: "Automatic Repair will fix your PC and then all done". Well thats wrong, is just crashed with the same Bluescreen Error Code.

After 50 times Bluescreen, is still crashes with the same Bluescreen Error Code. Then there is only one way too repair PC.

Didnt work. I want reinstall Windows 10 but, guess what, crash. Then i remove the SSD and is booted up, with Windows 10 Installation DVD, and it worked, then i pluged the SSD in my PC and, oh well, it crashed...

After over 100 times Bluescreen Error, without the Windows 10 DVD. The PC normal booted up. Is doesnt crashes anymore, is just loading... very long... very very long... I guess it was over 30 Minutes. I want force shutdown my PC because, is too long. I booted in Windows 10 DVD andddddddd... Ah not again, is still crashed with the same Bluescreen Error Code.

• Windows 10 installation USB/DVD doesnt work.
  
  • My PC doesnt support USB boot.
    
  • DVD doesnt work, it will just crash.
    
• Windows 10 Automatic Repair doesnt work.
  
• Windows 10 normal Boot doesnt work.
  

• Booting in HDD (not the SSD) (Windows 8.1/10) and it worked, but i want my data .
  
  • The PC will check my Harddisk and repair but without the SSD.