Windows 10: BSOD after BSOD...CPU issue??

Hello,I am trying to figure out what going on with my system. I built it back in October and it ran flawlessly until January. I started experiencing crashes and issues that we originally though were MB related. The MB was RMA's twice and finally replaced. I was running a MSI Tomahawk X570 WIFI at the time. When the board was initially sent in it was just crashing. After it was repaired twice and subsequently totally replaced I was never able to get the board to recognize the ASUS RTX 2070S in the PCIE_1 slot without forcing it to run in 8 lane. I have RMA'd the GPU and no cha

:)

 

7 different BSoD

Hey guys,

I have a serious problem. I make it as short as possible:

• system runs 100 % fine with the 10.12
• updatet to Catalyst 11.1 -> BSoD
• updatet to 11.1 Hotfix -> BSoD
• rollback to 10.12 -> BSoD
• removed ALL AMD files manually, installed 10.12 -> BSoD

• Temps are fine
• no sfc /scannow errors
• no chkdsk errors
• Prime, Furmark all fine
• regardless what driver I install -> BSoD
• I did no hw changes, no OC

Here are my BSoDs I receive:

• 0x0000010e
• 0x1000007e
• 0x0000007e
• 0x0000004e
• 0x0000003b
• dxgmms1.sys
• PFN_LIST_CORRUPT

They all refer to the GPU of course ...

From now on I receive a BSoD every time I try to play a game (especially BC2 and SC II) even if I completely remove the old driver and make a clean install.
Apparently the 11.1 damaged my system irreparable.

Any advice or info would be very much appreciated *Smile

 

Getting BSOD 0x124 error

Ignore what everone said here.

0x124 BSOD is usually related to VCCIO (VTT), run Prime95 version 26.6 with custom sizes of 512K to 640K with 50% of your memory for at least 8 hours.

If you get a 0x124 BSOD, increase VCCIO voltage by small steps, run Prime95 again until your stable.

If you pass Prime95 512K to 640K without a BSOD, then its Vcore too low. I'd suggest running IntelBurnTest with 80% of your memory to verify stability (8 to 12 hours).

Oh, and yeah, if this problem appeared all of the sudden, the reason is CPU degradation, you can prevent it by enabling C-States or adjust your overclock to use lower voltages.

 

PC reboots (no BSOD) on CPU stress

Hi fellow TPU members,

not too long ago, the box my gf's PC was transported in gave way on the stairs. Yes, you got it right, that sent a PC tumbling down a flight of steps alright.

Stuff broke. Also, stuff remained intact somehow.

I bought her a new case, new CPU cooler and we removed the floppy drive, so far so good. But the PC started crashing for no apparent reason, without a BSOD.

I tested:

• Memtest86+, left overnight, 0 errors
• Scanned the HDD for errors, nothing there
• Left FurMark burning up the GFX card and drawing some power, no problems there
• Ran Ubuntu from a Live CD doing nothing special, didn't crash
• Ran OCCT, Linpack, Prime95, all 3 caused reboots within minutes
• Oh, and I disabled "Restart on error" so I'm sure it's not a BSOD.

Now, I can still try and test something CPU intensive on Ubuntu, but my guess is the CPU didn't survive.
Before I do anything drastic like whippin' out the magic wallet and get her a new AMD quad, is there anything I didn't see?
I'm guessing the motherboard could be borkered as well, but can I check that other than replacing the CPU with a working one?
Any suggestions on which proggies I can use from an Ubuntu Live CD to stress the CPU?