Windows 10: BSOD After installing ssd

I installed a new Silicon Power 1tb NVME SSD and started getting bluescreens. I completely wiped my pc twice, removed my hdd so I know it's the ssd, Tried looking for firmware but their website has no firmware downloads because it goes to a no file found page and I am completely clueless on what to do next. I can start the pc fine, I can use the pc like normal, but randomly while playing games I get Bluescreened. Brother told me to come here so here I went and tried the log collector so I uploaded what it spat out so it's down there. Any help appreciated.

V2 Log collector file: DESKTOP-UDFC254-(2020-11-22_17-54-13)

:)

 

Z Book BSOD with Second SSD Drive

Hi all

I have an issue with an HP Z Book. It is a new Generation 6 device and came with a pre-installed second SSD drive.

All worked fine until I tried to put our corporate image onto the primary OS SSD.

Firstly, the new OS installed onto the secondary SSD rather than the primary.

So I disconnected/removed the secondary, recreated the partition on the primary and loaded our stock OS.

The machine now works absolutely fine, as long as I do not try to re-introduce the second SSD drive.

If I reinstall this, the machine boots up OK for a second or two and then BSOD's.

Can anyone suggest the reason for this issue - the BSOD message reported a kernel error.

Any ideas on steps to take to resolve this?

Thanks

Phil

 

Getting all kinds of BSOD while installing Windows 10 on an empty SSD

I was receiving a BSOD every 1-4 weeks (while working on Windows 10), wasn't able to figure out the cause of it. Tested RAM, SSD, all were good and I didn't pay too much attention.

Yesterday I've received another BSOD, didn't mind it, PC restarted and I saw a Windows message of "Automatic repair", which then resulted into "Repairing disk errors. This might take over an hour to complete.". Left it there for another 10 or so hours - it
was still running. Shut down the PC, took out the SSD (Samsung EVO 850, bought 6 months ago), backed up all the data, cleaned it, formatted and now trying to install windows on an empty SSD. Using a USB. These are the BSODs that I'm currently receiving when
trying to launch a Windows installation (by the way, same BSODs were appearing earlier "when everything was fine"):

• IRQL NOT LESS OR EQUAL
• SYSTEM SERVICE EXCEPTION
• KERNEL SECURITY CHECK FAILURE
• NTFS FILE SYSTEM
• MULTIPLE IRP COMPLETE REQUESTS
• BAD POOL HEADER

Already tried:

• reformatting the SSD
• reformatting the USB and flashing Windows installation to it
• tried using another USB
• switching RAM sticks (in total there are 4 of them, 8 GB each)
• BIOS default

PC parts:

• Motherboard: Asus B350-PLUS
• CPU: AMD Ryzen 1700
• RAM: G.Skill Flare X DDR4-2400 (4x8GB)
• SSD: Samsung 850 EVO (500 GB)

Any help will be greatly appreciated.

 

BSOD- atikmpag.sys

This is most likely due to an installation/upgrade error with ATI driver's. I suggest doing DriveSweeper and the following:

• Drivesweeper all drivers & in Safe Mode
• Unistall all drivers that aren't used in DriveSweeper (CCC Profiler Updates, MSI AfterBurner, anything related to ATI that use's it's drivers.)
• After you do this, the first thing you need to do is go into Device Manager and Unistall your ATI Drivers

Once your done, restart the PC and then try installing the latest drivers.


I had several issues with this in the past, but I overcame it with logical reasoning and whenever I have a driver issue, I just use these steps and I always overcome the problem.

Best of luck! *Toast :toast: