Windows 10: BSOD crash after installed proper drivers.

On Sun 9/15/2019 10:06:10 PM your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\091519-11734-01.dmp
This was probably caused by the following module: dxgkrnl.sys (0xFFFFF8054E615BEB)
Bugcheck code: 0x50 (0xFFFFC029FA1F748B, 0x0, 0xFFFFF8054E615BEB, 0x2)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\Windows\system32\drivers\dxgkrnl.sys
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: DirectX Graphics Kernel
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in a Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.



On Sun 9/15/2019 10:06:10 PM your computer crashed or a problem was reported
crash dump file: C:\Windows\MEMORY.DMP
This was probably caused by the following module: dxgkrnl.sys (0xFFFFF8054E615BEB)
Bugcheck code: 0x50 (0xFFFFC029FA1F748B, 0x0, 0xFFFFF8054E615BEB, 0x2)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\Windows\system32\drivers\dxgkrnl.sys
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: DirectX Graphics Kernel
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in a Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.



On Sat 9/14/2019 10:53:06 PM your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\091419-14031-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1C10A0)
Bugcheck code: 0xD1 (0xFFFFF801D58225FD, 0xFF, 0x75, 0xFFFFF801D58225FD)
Error: DRIVER_IRQL_NOT_LESS_OR_EQUAL
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that a kernel-mode driver attempted to access pageable memory at a process IRQL that was too high.
This bug check belongs to the crash dump test that you have performed with WhoCrashed or other software. It means that a crash dump file was properly written out.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Sat 9/14/2019 6:07:55 PM your computer crashed or a problem was reported
crash dump file: C:\Windows\Minidump\091419-11828-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1C10A0)
Bugcheck code: 0xFC (0xFFFF96030F2A3DC0, 0x8A0000065F6008E3, 0xFFFFDB8949C30420, 0x3)
Error: ATTEMPTED_EXECUTE_OF_NOEXECUTE_MEMORY
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that an attempt was made to execute non-executable memory.
This may be a case of memory corruption. More often memory corruption happens because of software errors in buggy drivers, not because of faulty RAM modules. Memory corruption can also occur because of overheating (thermal issue). There is a possibility this problem was caused by a virus or other malware.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



The link below is the dump file

https://1drv.ms/u/s!AkY3kTMT3NAfgaZqWwPvItwNG_PYMw?e=O0itKz



The link below is the Speccy link about my PC

http://speccy.piriform.com/results/zuGpTTklA7XWTEiwQ8GRgDu



:)

 

Flickering screen at startup, crashes, and BSOD after instaling new GPU

SO the Logs showed no errors at all during them times? They will be listed with a RED X Circle?????

Well if you just installed Windows 7 then make sure you have all your mobo drivers (chipset and all that stuff) from the mono vendor website, Then make sure you have your .net installed and updated as well as Direct X...THEN INSTALL THE AMD CATS!

 

BSOD- atikmpag.sys

This is most likely due to an installation/upgrade error with ATI driver's. I suggest doing DriveSweeper and the following:

• Drivesweeper all drivers & in Safe Mode
• Unistall all drivers that aren't used in DriveSweeper (CCC Profiler Updates, MSI AfterBurner, anything related to ATI that use's it's drivers.)
• After you do this, the first thing you need to do is go into Device Manager and Unistall your ATI Drivers

Once your done, restart the PC and then try installing the latest drivers.


I had several issues with this in the past, but I overcame it with logical reasoning and whenever I have a driver issue, I just use these steps and I always overcome the problem.

Best of luck! *Toast :toast:

 

Windows 10 Recurring Crashes


Hi Tom,

Welcome to the 10forums.

As this is not a BSOD problem, this is not the right part of the forum.
There are a few suggestions I would give you, NO garantee it will help!

Daemon tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known cause for BSOD's.
Please remove Daemon Tools and run the SPTD pass through remover.

1. Uninstall Daemon Tools
2. Download the SPTD standalone installer and follow these steps:
   • Double click the executable to open it
   • Click on the button shown below

If the button is grayed out, like in the image, there is no more SPTD installation on your system, and you can close the window



Warning Programs that claim to update your drivers install either the wrong or corrupted drivers.
If you have installed any driver with AVG Driver Updater, please remove them as it may cause trouble.