Windows 10: Bsod error after enabling driver verifier

Here are the dump files https://drive.google.com/file/d/1m2Bjz5Lvnbb9v2TSoxrb9BmoiqkWYqKA/view?usp=sharing

:)

 

BSOD hidclass.syss with verifier enabled

Hi DocSams,

Could you upload the memory dump, C:\Windows\MEMORY.dmp, to onedrive and post a share link. The minidumps provided severely lack in data.

If you haven't yet, please disable driver verifier.
Resetting driver verifier options (recommended in this order)

1. In normal mode open an administrator command prompt and enter the below command
2. In safe mode open an administrator command prompt and enter the below command
3. On 3 boot failures, you'll boot automatically to the recovery options,
   • click Troubleshoot
   • go to the advanced options
   • choose command prompt
   • enter the below command
4. Boot with the recovery media, see above 4 steps in option 3.
5. Via the recovery options or recovery media, select a restore point prior enabling driver verifier

Code:

 

Getting BSOD 0x124 error

Ignore what everone said here.

0x124 BSOD is usually related to VCCIO (VTT), run Prime95 version 26.6 with custom sizes of 512K to 640K with 50% of your memory for at least 8 hours.

If you get a 0x124 BSOD, increase VCCIO voltage by small steps, run Prime95 again until your stable.

If you pass Prime95 512K to 640K without a BSOD, then its Vcore too low. I'd suggest running IntelBurnTest with 80% of your memory to verify stability (8 to 12 hours).

Oh, and yeah, if this problem appeared all of the sudden, the reason is CPU degradation, you can prevent it by enabling C-States or adjust your overclock to use lower voltages.

 

BSOD hidclass with driver verifier

Hi Doc_Samson,



Thank you for writing to Microsoft Community Forums.



I understand that you receive Blue Screen error with hidclass.sys. In order to get to the root cause of the issue, we will need the Dump files, so that we can analyze them and assist you accordingly. I have sent a private message to you, please share
the Dump files over the private message.



To access Private Message click on your Profile on the top right corner, then click on the ellipses, and select
View Private Messages.



However, the hidclass.sys is a driver file for Human Interface Devices, which are basically, keyboard/mouse or gaming controllers. I would suggest you to disconnect all the external devices and see if that helps.



I would suggest you to refer the steps mentioned below and see if that helps:



Method 1: Update drivers



I suggest you to update the drivers on the computer, to make sure that all the drivers are up to date including Keyboard, Mouse, USB and HID Drivers. In addition, you may also update the chipset drivers from the computer manufacturer’s websites. Kindly
refer the article
Update drivers in Windows 10.



Method 2: Check hard disk for errors



I would suggest you to run chkdsk utility to check any errors in the hard drive. Refer the steps mentioned below:

1. Type command prompt in the search bar on the
   Taskbar.
   
2. Right click on the command prompt icon and select
   Run as administrator.
   
3. Now, paste the following command and hit Enter: chkdsk/f C:
   
4. Select Yes and restart the computer.
   

Note: While performing chkdsk on the hard drive if any bad sectors are found on the hard drive when chkdsk tries to repair that sector if any data available on that might be lost



Method 3: Windows Memory Diagnostic



You can also run Memory Diagnostic on the computer to check for any memory corruption errors. Follow the steps mentioned below:

1. Press Windows key + R, to open
   Run dialog box.
   
2. Type mdsched and click on
   OK.
   
3. Click on Restart now and check for problems.
   

You may want to refer the troubleshooting steps mentioned in the article

Troubleshoot blue screen errors.



You can also refer the suggestions provided by auggy replied on May 15, 2018 in the thread

BSOD Hidclass.sys.



Let us know how it goes.



Regards,

Nikhar Khare

Microsoft Community - Moderator