Windows 10: BSOD ever since update drivers

So I used CCleaner to updated my drivers and now it messed up my laptop. I got BSOD everytime I shutdown and turn on the laptop, also happened when I put my laptop to sleep, restarting is normal, nothing happened. This is my recent dump files that I used WinDbg to opened: KERNEL_DATA_INPAGE_ERROR 7a The requested page of kernel data could not be read in. Typically caused by a bad block in the paging file or disk controller error. Also see KERNEL_STACK_INPAGE_ERROR. If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185, it means the disk subsystem has experienced a failure.

:)

 

BSOD- atikmpag.sys

This is most likely due to an installation/upgrade error with ATI driver's. I suggest doing DriveSweeper and the following:

• Drivesweeper all drivers & in Safe Mode
• Unistall all drivers that aren't used in DriveSweeper (CCC Profiler Updates, MSI AfterBurner, anything related to ATI that use's it's drivers.)
• After you do this, the first thing you need to do is go into Device Manager and Unistall your ATI Drivers

Once your done, restart the PC and then try installing the latest drivers.


I had several issues with this in the past, but I overcame it with logical reasoning and whenever I have a driver issue, I just use these steps and I always overcome the problem.

Best of luck! *Toast :toast:

 

BSOD hidclass with driver verifier

Hi Doc_Samson,



Thank you for writing to Microsoft Community Forums.



I understand that you receive Blue Screen error with hidclass.sys. In order to get to the root cause of the issue, we will need the Dump files, so that we can analyze them and assist you accordingly. I have sent a private message to you, please share
the Dump files over the private message.



To access Private Message click on your Profile on the top right corner, then click on the ellipses, and select
View Private Messages.



However, the hidclass.sys is a driver file for Human Interface Devices, which are basically, keyboard/mouse or gaming controllers. I would suggest you to disconnect all the external devices and see if that helps.



I would suggest you to refer the steps mentioned below and see if that helps:



Method 1: Update drivers



I suggest you to update the drivers on the computer, to make sure that all the drivers are up to date including Keyboard, Mouse, USB and HID Drivers. In addition, you may also update the chipset drivers from the computer manufacturer’s websites. Kindly
refer the article
Update drivers in Windows 10.



Method 2: Check hard disk for errors



I would suggest you to run chkdsk utility to check any errors in the hard drive. Refer the steps mentioned below:

1. Type command prompt in the search bar on the
   Taskbar.
   
2. Right click on the command prompt icon and select
   Run as administrator.
   
3. Now, paste the following command and hit Enter: chkdsk/f C:
   
4. Select Yes and restart the computer.
   

Note: While performing chkdsk on the hard drive if any bad sectors are found on the hard drive when chkdsk tries to repair that sector if any data available on that might be lost



Method 3: Windows Memory Diagnostic



You can also run Memory Diagnostic on the computer to check for any memory corruption errors. Follow the steps mentioned below:

1. Press Windows key + R, to open
   Run dialog box.
   
2. Type mdsched and click on
   OK.
   
3. Click on Restart now and check for problems.
   

You may want to refer the troubleshooting steps mentioned in the article

Troubleshoot blue screen errors.



You can also refer the suggestions provided by auggy replied on May 15, 2018 in the thread

BSOD Hidclass.sys.



Let us know how it goes.



Regards,

Nikhar Khare

Microsoft Community - Moderator

 

Windows update keeps replacing ALPS Touchpad driver with a Synaptics driver.

Hi,

Thank you for posting your query in Microsoft Community. Appreciate your interest in using Windows 10.

I suggest you to uninstall and delete the previous drivers and the latest drivers for the touchpad and install the required version of the driver from Device Manager by following the steps below:

• Press Windows key + X and select Device Manager from the list.
• Expand the Touch pad driver.
• Right click on the driver and click on update/install.
• Select the required version from the on-screen prompts.

And for the problem with the installation of printer drivers, I suggest you to run the Windows Update troubleshooter by following the steps below:

• Type “Troubleshooting” in search box and press Enter.
• Click on “View All” option on top left pane.
• Select “Windows Update” from the list and follow the prompts for troubleshooting.

Hope the information is helpful. Feel free to
write to us for any other assistance with Windows, we’ll be glad to assist you.