Windows 10: BSOD Help.

I only opened the dump of today (18th) *Wink
It may be old as you might have changed it already, but the dump is the most recent and the only one of 18th this month.

 

Code: BugCheck 12B, {ffffffffc00002c4, 6a, 2610f2b4380, ffffd00021cda000} *** WARNING: Unable to verify timestamp for win32k.sys *** ERROR: Module load completed but symbols could not be loaded for win32k.sys Probably caused by : ntkrnlmp.exe ( nt!ST_STORE<SM_TRAITS>::StDmPageError+ec ) Followup: MachineOwner --------- 2: kd> !analyze -v ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* FAULTY_HARDWARE_CORRUPTED_PAGE (12b) This bugcheck indicates that a single bit error was found in this page. This is a hardware memory error. Arguments: Arg1: ffffffffc00002c4, virtual address mapping the corrupted page Arg2: 000000000000006a, physical page number Arg3: 000002610f2b4380, zero Arg4: ffffd00021cda000, zero[/quote] And the above would match if you have two different sticks currently plugged in the computer.

 

Weird, well according to me, and my system the one 1600 stick is out, I put it in a plastic bag and in my electronics drawer, so I don't lose it and it doesn't get damaged, but hopefully the information you have in there, will help you if my computer isn't all good now, I can tell you, I'm sad that the crashes during reinstallation weren't saved (to reinstall windows I had to fully format my hard drive so... I lost everything that I didn't back up)

 

And the above would match if you have two different sticks currently plugged in the computer.[/quote] I'm not completely sure what I'm looking at but, may I ask, that despite running memtest 86 set to 8 passes and getting no errors with the ram, do you think it's possible, buying a whole new set altogether would wipe out the problem?

 

Memtest86+ with 8 passes doesn't per se have to rule out the memory completely, it normally does but it does also occur that errors show up when you run MemTest86+ till all passes have finished.

 

I mean I was just debating when I get more money, in either 2 weeks, or 4 that I was gonna buy a set of G.skill ripjaws x series, 32 gigabytes, since I couldn't find a set of 16 for my motherboard, I could only find 32's... But I was going to just replace the ram to see if that helped at all. Well it's 4:45 AM here, I'm gonna go to sleep, I'll leave my computer running over night, I'll let you know if it crashes, and I'll check anything you post tonight, in the morning!

 

DarkChrono here is a pdf of memory qvl(qualified vendors list) for your motherboard:
ASUS M5A97 LE R20 Memory QVL

And as far as I can see there are a couple of 16GB kits you can get, but all of those are 4x4GB.

 

Yeah, to me that's a waste if I'm going to use all 4 slots I'd rather just get 32 gigabytes you know? Also, despite being ordered at like 7 pm yesterday, and three day shipping I got my graphics card today, so I already swapped the old one out, put the new one in, updating graphics driver now, uninstalling the old one's drivers (they're two different makers, so... Old was Nvidia new is AMD.
So, I just had another BSOD a few minutes ago, MEMORY_MANAGEMENT I ran the dm log and uploading now, god I just want these crashes to stop.

I went to launch a game, and another BSOD, so... Here's the dmp for this, it's Critical_Structure_Corruption. the 1.35 mb is the most recent... I'm just gonna sit here staring at the forums in horror because I can't deal with all of the BSOD's RAN SFC /SCANNOW and it did everything but it said there were some things it couldn't fix, I'm restarting to run Windows Memory Diagnostic, to see if it says it's the ram, then I'm doing the dm tool again, and putting the SFC error pages into the folder with it and uploading it for you guys.

Edit: not even 20% into the first pass and it says "hardware problems detected. To identify and repair these problems, you will need to contact the computer manufacturer. Although this test may appear inactive at times, it is still running." Blah blah blah.

 

I'm sorry in advance for double posting but, would it be safe to take the two ram sticks out and put the single 1600 mhz ram stick in, and run the test again?

 

I'm not sure if sticks from a kit can run alone.

 

The 1600 wasn't a kit, it came standalone with the desktop, I accidently mixed it in with the other 4 and ended up getting rid of the 4th of the 1333 kit, so the 1600 was stand alone.

 

I misread a post, if it came single you should be able to run with it *Smile

 

Should I pull them, and put the 1600 in slot one, and run normally, try some games, and if it crashed, run the dm log and re upload here?

I pulled the 1333's and put the standalone 1600 in, so, if I get anymore BSOD's I'll post here, for now I'm gonna try to launch Subnautica (the game I launched earlier that crashed me)

 

So, no crashes of any kind since pulling and putting the single 8 gig stick in, I'm going to end up ordering a 16 gig 4x4 G.Skill ripjaws set sometime soon, PC runs amazingly, thank you guys for all your help! Will come back in the future with any questions/problems, or concerns! @BorisTheAnimal @axe0 @z3r010 thanks again soo much!

 

No problem DC, happy to help!