Windows 10: BSoD loop - no crowdstrike

Hey folks,what happens/ happend: I browsed the web, then my PC crashed and booted again. Right after that it restarted with the screen stating “ASrock” on top and in the bottom saying “Preparing automatic repair”. The PC crashes again after that. Now the PC restarts with the same ”ASrock” statement but WITHOUT “PREPARING AUTOMATIC REPAIR”. Then it crashes, restarts and the “ASrock screen comes WITH “PREPARING AUTOMATIC REPAIR”, then it crashes. the different “ASrock” screens always switch! The error code doesn’t change in any bit.As the automatic repair fails I can assume the safe mode to not

:)

 

bsod loop device verifier ionmanager violation

Hi Tom,

To better assist you, provide the answers to the following questions:

• Have you made any changes on your device prior to the issue?
• What is the complete error message that you're seeing on the screen?

For the meantime, we suggest checking the answers on the following threads below which we found similar and helpful in resolving the issue:

Windows 10 Driver Verifier BSOD loop.. how to get out of it?

Windows 10 stuck in bsod reboot loop

Let us know if you need further assistance.

 

Windows 11 BSOD Loop

Hello, any thoughts welcome. Desktop PC, 4 years old, Intel i7, 32GB Ram, SSD M2, etc. Was running Win 10, upgraded to Win 11 back in April 2022. Last month or so PC started to have BSOD looping. When it loops, some times I get as far as fully logging in and maybe doing 5 mins of work before it crashes, other times, it will BSOD at login screen before I even login in. and just boot up and loop around agin. finally it will stabalise and might be fine for a while (can be hour or days).

Issues seemed to start when running MS Teams in MS Edge browser, and got a message within MS Teams in the browser saying "memory running low". I have tried everything and in the end have wiped the PC, formatted, updated BIOS and done a very clean, minmal build 4 days agao, from this morning, PC BSOD loops again. Was very stable for a few days. I have run SFC, Memory test, almost every test I can find, updated all drivers, etc, passes all. I'm not sure if issue is Hardware or Software. There are odd Software issues outside of BSOD, for example, all my Quick Links in Windows Explorer have gone now, I open documents and formatting has changed, and on the login screen it sometimes loses my pin and details and says nothing is set up, restart and will be there again.

List of BSOD errors on 8/9/2022 over an hour or so in order:

IRQL Not Less or equal (BSOD)

PFN List Corrupt (BSOD)

Kernal Secuirty Check Failure (BSOD) (Teams in Edge frezzing before hand)

IRQL Not Less or equal (BSOD)

PFN List Corrupt (BSOD)

Kernal Secuirty Check Failure (BSOD)

Critical Process Died (BSOD)

Driver Overran stack Buffer (BSOD)

System thread Exception ACPI.sys (BSOD)

Memory Management (BSOD)

System Service Exception (BSOD)

System Service Exception (BSOD)

PFN List Corrupt (BSOD)

Memory Management (BSOD)

System Service Exception Not handled (BSOD)

System Service Exception Not handled (BSOD)

Page Fault In Nonpaged Area (BSOD)

PFN List Corrupt (BSOD)

Memory Management (BSOD)

Critical Process Died (BSOD)

Kernal Secuirty Check Failure (BSOD)

Critical Process Died (BSOD)

Bad Pool Header (BSOD)

PFN List Corrupt (BSOD)

PFN List Corrupt (BSOD)

 

CrowdStrike Falcon Sensor Installation Failure

Hello,

We are working through deploying CrowdStrike as our new IDS/IPS and had a few machines decide not to cooperate. I have been in contact with CrowdStrike support to the extent they told me I need a Windows specialist.

So far I have run CrowdStrike's Windows diagnostic tool, A "Get-InstallerRegistration.ps1" from CrowdStrike support, collected a Windows Installation Log during install attempt, and also run Windows ProcMon during Installation.

When running the installation a dialogue box appears that says, "Service 'Crowdstrike Falcon Sensor Service' (CSFalconService) could not be installed. Verify you have sufficient privileges to install system services.'

I do have admin rights, have right-clicked and Run as Admin.

Any help is appreciated.