Windows 10: BSOD on install from USB

Have an HP Notebook 14-cf0013dx, 8gb ram, 1TB HDD 5200rpm (full specs are in profile)

Attempting to reinstall windows after BSOD on start, mostly page fault in non paged area BSOD error but can also be irql not less or equal, or Kernel Secure check failure. Saw another one or two but cannot recall at the moment.

Symptoms. Can boot to USB in UEFI or legacy and Load the windows 10 install made from the windows creation tool. The loading files completes. The system restarts and the HP splash screen appears with the windows 10 dots circling underneath for about 2 revolutions then a BSOD.

First steps:
Tried windows 10 recovery. over 48 hours still not completed.
Ran HP hardware diagnostics, Memory HDD, system board all passed.
Ran memtest86 from Hirens Boot CD. passed.
Ran seagate HDD test. passed.
Tried windows 10 USB install after each step above.
Tried Windows 10 safe mode installation, was able to get through installation but on reboot the same results, BSOD within 3 revolutions of startup dot-circle.

Second steps:
Removed HDD, hooked up to main computer and did a CMD, DISKPART, CLEAN
Updated BIOS to most recent version F.53 to support windows 10 v.1909
Moved DIMM from slot 1 to slot 2
Tried HP cloud recovery with exact same results as listed above.
Tried Windows 10 USB safemode install again same results. Was able to complete installation from USB but BSOD on restart.

Short of replacing the Motherboard due to the integrated graphics memory (which still tested good in HP system board test), I am at a loss. Please help with any suggestions.

:)

 

Installing windows off of a USB stick

Step By Step from vista:
From admin cmd prompt

1. diskpart
1a. list disk
2. select disk 1 (replace 1 with your usb drive)
3. clean
4. create partition primary
5. select partition 1 (replace 1 with your usb drive)
6. active
7. format fs=fat32
8. assign
9. exit

Copy Windows Vista's DVD ROM content to the Flash Drive

xcopy d:\*.* /s/e/f e:\ (d being your vista cd and e being your usb stick)

And that's it, boot off your usb disk

 

BSOD- atikmpag.sys

This is most likely due to an installation/upgrade error with ATI driver's. I suggest doing DriveSweeper and the following:

• Drivesweeper all drivers & in Safe Mode
• Unistall all drivers that aren't used in DriveSweeper (CCC Profiler Updates, MSI AfterBurner, anything related to ATI that use's it's drivers.)
• After you do this, the first thing you need to do is go into Device Manager and Unistall your ATI Drivers

Once your done, restart the PC and then try installing the latest drivers.


I had several issues with this in the past, but I overcame it with logical reasoning and whenever I have a driver issue, I just use these steps and I always overcome the problem.

Best of luck! *Toast :toast:

 

7 different BSoD

Hey guys,

I have a serious problem. I make it as short as possible:

• system runs 100 % fine with the 10.12
• updatet to Catalyst 11.1 -> BSoD
• updatet to 11.1 Hotfix -> BSoD
• rollback to 10.12 -> BSoD
• removed ALL AMD files manually, installed 10.12 -> BSoD

• Temps are fine
• no sfc /scannow errors
• no chkdsk errors
• Prime, Furmark all fine
• regardless what driver I install -> BSoD
• I did no hw changes, no OC

Here are my BSoDs I receive:

• 0x0000010e
• 0x1000007e
• 0x0000007e
• 0x0000004e
• 0x0000003b
• dxgmms1.sys
• PFN_LIST_CORRUPT

They all refer to the GPU of course ...

From now on I receive a BSoD every time I try to play a game (especially BC2 and SC II) even if I completely remove the old driver and make a clean install.
Apparently the 11.1 damaged my system irreparable.

Any advice or info would be very much appreciated *Smile