Windows 10: BSOD on only cold boots

I got a custom built pc for christmas and it has been getting BSOD's since it was built and they have only been happening on cold boots, and the file that is having problems is ntoskrnl. I would love if someone could find the problem that has been going on for weeks.

:)

 

BSOD's and system freezing

Don't you think it's strange it almost only happens on cold boots? When the system is running, it only BSOD's sometimes, does happen though..

 

BSOD's and system freezing

I have had 2 BSOD's after a cold boot, computer has been off for a couple of hours, it didn't seem to have any problem after removing Avast, but this usually happens with a cold boot.

KMODE_EXEPTION_NOT_HANDLED

KERNEL_SECURITY_CHECK_FAILURE

There was only 1 minidump file: https://1drv.ms/u/s!AlCKB9lAV-vAgcwV927cBD3657gsfQ

 

Hi Colinator01,

Welcome to the 10forums.

Please uninstall OpenHardwareMonitor, the last update was in december 2013 and it uses a very old driver.

Please check MSI for driver updates for the sata controller drivers, I believe they are included in the chipset but can't say for sure.
MSI Global 64

Please uninstall the AMD software for the time of troubleshooting, the driver below is used with AMD software, is old and is known for causing bluescreens in Windows 7.
I know that Windows 10 and Windows 7 are 2 different operating systems, but I would like to start with getting rid of the old drivers.
Code: c:\program files\amd\ati.ace\fuel\amd64\aoddriver2.sys[/quote]

 

The latest sata controller driver is windows 8.1 is that ok?

What do you mean by uninstall amd software? as in the catalyst installer? because when i uninstalled it and tried downloading the sata controller driver it told me that i needed the amd catalyst installer

 

Best is for Windows 10.

First uninstall AMD Catalyst, then install the sata controller drivers with a custom/advanced installation to ensure as less as possible software.

 

Please keep me posted on any improvements or problems.

 

Turned my computer on and its the same old blue screen. When I start it up it usually blue screens 2-3 times then goes into automatic repair and after that its fine.

 

When does the crash occur?
What error codes are displayed?

 

It only crashes on start up just before it goes to windows and the main 3 error codes I get are system service exception, system thread exception not handled, and kmode exception not handled. There are a bunch of other error codes I have gotten that aren't as consistent.

 

Could you run the DM Log Collector (from the BSOD Posting Instructions) again and upload a new zip please.

EDIT: for testing purpose, please disable fast startup if it is enabled
Fast Startup - Turn On or Off in Windows 10 - Windows 10 Forums

 

Here is the dump with multiple blue screens after turning fast startup off.

I also used drivermax to update all outdated drivers.

 

-1 for drivermax

You need to remove those drivers before we can continue in order to prevent more problems then already present.

 

Ok I did a system restore to the point in which just before i installed driver max, but I still have the sata control driver from msi. What is the next step?

 

Diagnostic Test

DRIVER VERIFIER


Warning Please make a backup of your important files and get your rescue media or create one.
Please create a restore point.
Please follow this tutorial to run driver verifier.

Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

Driver verifier should be performed for a max of 48 hours, or when you have a bluescreen, whatever comes first.

If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.



Note Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.