Windows 10: can i avoid taking window update for 4-5 months

can i avoid taking window update for 4-5 months as i m facing problem in viewing my paid lectures.

is there any threat to my pc

:)

 

Update Windows 10 after 5 months in storage?

Hi Nitram,

Thank you for posting in Microsoft Community and being a part of Windows 10.

I understand your concern about installing the latest updates on your device.

Do let us know the following to assist you better:

• Which were the updates you found to be installed on youe device?
• Did you check if those update are already installed under View installed updates?
• What exactly do you mean by: "My PC has been in storage for 5 months"?

Try the below troubleshooting steps and check if it helps.

Step 1: I suggest you to check if those updates are already installed:

Follow:

• Right click on the Start button and select Programs and Features.
• Click on View installed updates.
  

Step 2: Disable anti-virus software.

NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you shouldn't disable your antivirus software. If you have to temporarily disable it to install
other software, you should re-enable it as soon as you're done. If you're connected to the Internet or a network while your antivirus software is disabled, your computer is vulnerable to attacks.

If the issue still persists, I suggest you to uninstall the anti-virus software.

Step 3: I suggest you to
run Windows Update troubleshooter.

Windows Update troubleshooter resolves problems that prevents you from updating windows.

Steps:

• Press Windows + X, click on Control Panel, select
  Category and then select Large or Small icons.
• Click on Troubleshooting and click on
  View all in the left pane.
• Select Windows Update to run the Windows Update Troubleshooter
  and follow the on-screen instructions.

Hope it helps. Try the above and get back to us with an updated status of this issue for further assistance.

 

AMD FX OC'ers Club

That's what the auto setting will do since you're over the 1333 mark it jumps to the next step which isn't listed or officially supported I assume by that ram.

At this point though I would suggest dropping the multi one step or .5 so that we can get something stable and possibly take the heat issue out of the picture for now.

 

Problem updating Windows Surface Pro 4 with Windows 10 feature updates

Hi,

I have manage to install image for Microsoft Surface Pro 4 by going to https://support.microsoft.com/en-us/...erecoveryimage and download a recovery image for Microsoft Surface Pro 4.

What I did to reset your Surface from a USB recovery drive was:
Step 1: Make sure your Surface is turned off and plugged in (hold down the power
button for 30 seconds).
Step 2: Insert the USB recovery drive into the USB port on your Surface.
Step 3: Press and hold the volume-down button while you press and release the
power button on your Surface.
Step 4: When the Surface logo appears, release the volume button.
Step 5: When prompted, select the language and keyboard layout you want.
Step 6: Select Troubleshoot > Reset your PC.
If prompted for a recovery key, select Skip this drive at the bottom of the
screen.
Step 7: Select the target operating system you wish to reset. This
refers to the current operating system installed on your Surface.
Step 8: Select Yes, repartition the drives, and on the next page, select Next.
Step 9: Choose Just remove my files.
Step 10: Select Reset.
Surface restarts and the Surface logo displays while the reset process continues
(this can take a while).

This always fails and I have to do the below which continues installation.
Windows 10 Installation Media:

1. Insert the Media (DVD/USB) in your PC and restart.
2. Boot from the media.
3. Select Repair Your Computer.

Select Troubleshoot.

1. Choose Command Prompt from the menu:

Type in the command:
Diskpart
Type in the command:
List disk (Note which disk is your Boot drive number mine is 0)
Type in the command:
Sel disk 0
Type in the command:
List vol (Note which volume is the EFI partition mine is 4)
Type in the command:
Sel vol 4
Type in the command:
assign letter=V:
Type in the command:
Exit
Type in the command:
V:
After you have assigned a drive letter Using Diskpart You can format the EFI partition:
Example: if you assigned a letter V to the partition the command would be:
format V: /FS:FAT32
Type in the command:
bcdboot C:\windows /s V: /f UEFI


Now I have an issue that I cannot install Feature Updates. They keep failing to install.
Any ideas how to resolve issue?