Windows 10: Can't figure out how to install Teredo

So I bought state of decay 2 to play with my buddies. I cannot join or host games though. I get the error 1006. I have tried to get Teredo to work through the command prompt and through the device manager where you use legacy hardware. When I attempted to alter the program through command prompt, and I have gotten it to the point where my NAT is strict. I cannot change it to medium or open, and again the program doesn't even show up on device manager (yes I pressed display hidden devices). I need help getting it to work, and I feel the easyiest fix would be if there is some file i could just download.. Please help

:)

 

No Teredo installed

Hi Jay,

Thank you for writing to Microsoft Community Forums.

Before we proceed, could you please confirm a few things for me?

1. The make and model of your system?
   
2. The Windows 10 Build you are using?
   

Systems communicate with one another using a certain predefined set of protocols, when systems within a network are using different protocols but are trying to communicate with one another it may require a translator to enable
this communication. This is where the Teredo Tunneling comes in. It facilitates the connectivity between devices behind routers that use network address translation (NAT) and thus enable this communication.

Given that you have already tried to enable the Teredo through the device manager and the netsh command through the command prompt, we have a few more steps that we could try to resolve this issue.

Check and make sure that no VPN client is blocking the Teredo connectivity.

Steps:

Manually enable the Teredo through the registry.

Disclaimer: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these
steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs.

To take a backup or restore the registry click
here.

Check the iphlpsvc registry path:

1. Right-click the Start icon, type in cmd, Right-click on it and 'Run as administrator'.
   
2. Run the following command from the Admin command prompt: reg query HKLM\System\CurrentControlSet\Services\iphlpsvc\Teredo
   
3. If you find this output: Type REG_DWORD 0x4
   
   You will need to Re-enable Teredo by running the following command from the Admin command prompt: netsh interface Teredo set state type=default
   

Check the TcpIp6 registry path:

1. Right-click the Start icon, type in cmd, Right-click on it and 'Run as administrator'.
   
2. Run the following command from the Admin command prompt: reg query HKLM\System\CurrentControlSet\Services\TcpIp6\Parameters
   
3. If you find the output, and the value displayed is not 0x0. Example: DisabledComponents REG_DWORD 0x8e
   
4. You will need to Re-enable Teredo by running the following command from the Admin command prompt: reg add HKLM\System\CurrentControlSet\Services\Tcpip6\Parameters /v DisabledComponents /t REG_DWORD /d 0x0
   

Hope it helps.

Aaron Summith

Microsoft Community - Moderator

 

Teredo Adapters not installed

Hi,

Incorrect configuration setting is one of the possible reason why you're unable to install the Teredo Adapters on your computer. To help you resolve this concern, we suggest that you follow the solutions provided on the link below:

Click here

You may also check out this
link for additional troubleshooting steps.

If the issue persists, we highly recommend that you contact your router manufacturer to help you install the Teredo Adapter on your device.

Kindly notify us with the results.

 

Can You Please fix the teredo adapter problem already?

Hi Mr Overshield,

Teredo being disabled is one of the possible reasons why you're unable to fix the Teredo problem as well as can't find it under hidden devices. To re-enable your Teredo on your device, I suggest that you follow the steps below:

1. Type in cmd in to the search bar on your desktop and right click on Command Prompt and run it as admin.
   
2. Type in netsh interface Teredo set state type=default
3. Kindly restart your computer to let the changes take effect.

Note: No need to reinstall the Teredo as it will install itself.

For additional information and troubleshooting steps, you may visit the link below:

Click here

Kindly update us with the results, so that we can assist you further.