Windows 10: Can't force Factory Reset after installing tablet drivers

I was installing the drivers for my Wacom, it gave me a blue screen PAGE FAULT IN NON PAGED AREA and it sent me to advanced options. I tried to return to a recovery point WITHOUT the drivers but the problem persisted.When i tried to return to the oldest recovery point it gave me another BSOD..Once it sent me back to advanced options i tried to factory reset my laptop.....now i get "there was a problem resetting your pc".I'm frustrated and I don't know what to do...is there a way to at least factory reset? I can't reset from command prompts and it won't boot safe mode CRITICAL PROCESS DIED

:)

 

Factory reset tablet stuck.


So I updated my tablet from 8.1-10.
There were some issues so i reinstalled some drivers and the issues continued so i did a factory reset.
The reset stopped halfway and wont continue.
The screen is mostly blank unless i fiddle with some things and a screen comes up asking if I want to continue to update, reset factory settings, trouble shoot, use usb or cd or continue the reset.
I have tried the reset a few times but it has not worked.
Amazon.co.jp： マウスコンピューター 8.9型Win8.1タブレット･2in1 PC Office付 (Win8.1/AtomZ3735F/2GB/32GBeMMC/Office HB) WN891: パソコン・周辺機器
This is the tablet here. Unfortunately everything is also all in Japanese, which i understand somewhat but am kind of winging it.

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

 

Fusion 5 tablet stuck on restart

Hi, Holly Nies

Welcome to the Microsoft Community.



It sounds like your Fusion 5 tablet is stuck in a boot loop. This can be caused by a number of factors, including a software update gone wrong, a corrupted operating system, or a hardware issue.

Here are some steps you can try to fix your tablet:

1. Force restart your tablet. To do this, press and hold the power button for at least 30 seconds. If your tablet restarts, try turning it on normally.
   
2. Boot your tablet into safe mode. Safe mode is a diagnostic mode that starts your tablet with only the essential software running. To boot your tablet into safe mode, follow these steps:
   
   • Press and hold the power button until the tablet turns off.
     
   • Press and hold the power button again until the Fusion logo appears.
     
   • When the Fusion logo appears, release the power button and immediately press and hold the volume down button.
     
   • Continue holding the volume down button until the tablet boots into safe mode.
     
   If your tablet boots into safe mode, you can try uninstalling any recently installed apps or updates that may be causing the boot loop.
   
3. Factory reset your tablet. If none of the above steps work, you may need to factory reset your tablet. This will erase all of your data, so be sure to back up your important files before proceeding. To factory reset your tablet, follow these steps:
   
   • Press and hold the power button until the tablet turns off.
     
   • Press and hold the power button and the volume up button at the same time.
     
   • Continue holding the power button and the volume up button until the tablet boots into the recovery menu.
     
   • Use the volume down button to navigate to the “Wipe data/factory reset” option.
     
   • Press the power button to select the “Wipe data/factory reset” option.
     
   • Use the volume down button to navigate to the “Yes – delete all user data” option.
     
   • Press the power button to select the “Yes – delete all user data” option.
     
   Your tablet will now begin the factory reset process. Once the process is complete, your tablet will reboot.
   

If you have tried all of the above steps and your tablet is still stuck in a boot loop, you may need to contact Fusion customer support for assistance.

Note:

• If your tablet is under warranty, you may be able to get it repaired or replaced for free.
  
• If your tablet is not under warranty, you may need to pay for repairs.
  

Best Regards

Martin | Microsoft Community Support Specialist