Windows 10: "Device Security" no longer compatible after PC reset

I reset my pc yesterday, and it deleted all my drivers, I downloaded them again from my PC's official site MyASUS app->User manual->Drivers & Tools, to be sure, I also redownloaded my AMD processor's driver in it's official site AMD support->AMD Adrenalin Edition->Download all missed drivers, and restarted my PC but my Windows 11 still says "The page you are trying to access has no supported features and is not available.", when I click on it, it says "Standard hardware security not supported; Your device does not meet the requirements for standard hardware security. Device

:)

 

Cast-to-Device Function on Windows 10 PC no longer working

Hello Jeff,

Thank you for posting on Microsoft Community. We will assist you in resolving the issue.

The issue you are facing with is device specific. You should update the device drivers compatible to the new operating system to which you upgraded to for fine and smooth working of the device.

I suggest you to download the latest device drivers for Samsung by visiting the manufacturer’s website and check if the issue is resolved.

If the issue persist, I suggest you to install the driver is compatibility mode by following the steps below and check if the issue is resolved.

Step 1: Compatibility mode runs the program in the current version of Windows using the settings from previous version of Windows.

• Download the latest driver setup file from the manufacturer’s website or locate the driver setup file of the previous operating system in your PC.
• Right-click on the driver setup file and click on properties.
• Click on the compatibility tab, check the box
  Run this program in compatibility mode for, select Windows 10 operating system from the drop down menu and proceed with the installation.
• Once the driver is installed in compatibility mode,
  restart the PC for the effective changes to take place.

Step 2: You can also follow the steps below and check if the issue is resolved.

Press Windows logo key on the keyboard and type Run programs made for previous versions of Windows.

• Select the top most search result and follow from step 2 from the article
  
  Make older programs compatible with this version of Windows (Also applies to Windows 10).
  

Write back to us with the status of the issue on the same post for further assistance. Your reply is most important for us to ensure we assist you accordingly.

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

 

Bluetooth is no longer compatible after upgrading to Windows 10

Hi Deborah,

Welcome to Microsoft Community.

We regret for the inconvenience caused to you. I will be glad to assist you with this issue.

I suggest you to run the Hardware and Devices Troubleshooter and check if it helps.

Step 1: The Hardware Troubleshooter is an automated tool which checks the hardware connected to the computer for any known issues and provides the details on how to fix them. Follow these steps to run the troubleshooter.

• 
  Click Start.
  
• 
  Type Troubleshooting in the search bar and press “Enter”.
  
• 
  In the “Troubleshooting” window, click on
  “View All” on the left pane.
  
• 
  Click on “Hardware and Devices”.
  
• 
  Click on “Advanced” and then click on “Run as Administrator”.
  
• 
  Click “Next” and follow the on-screen instructions to complete the troubleshooting process.
  

Step 2: You can also update the Bluetooth drivers via Device manager and check if it helps.

• Press Windows + X key and select
  Device Manager.
• Check for Bluetooth drivers.
• Right click on it and select Update.
• Restart your system after performing the steps and check if it helps.

Step 3: Download and save the AMD driver on the desktop.

Install the driver in compatibility mode.

• 
  Right click on the driver, and click on
  Properties.
  
• 
  Go to the Compatibility tab.
  
• 
  Check the box for Run this program in compatibility mode for:
  
• 
  Select Windows 8.1
  (or any compatible OS version) in the list of Operating systems.
  
• 
  Click OK.
  
• 
  Double-click the driver file to install the driver and follow the onscreen instructions.
  

Reboot your computer.

Keep us posted on the issue to assist you better.

Thank You.