Windows 10: Different blue screen errors when I boot up my pc

So last night I was on my computer talking to my friends and it randomly blue screened me out of no where, it restarted and I got logged back in and then it blue screened me again with a different message this time, booted up again and I got another different message! I’m sitting here now trying to fix the problem and I got another different blue screen error! I really don’t know what to do at this point as my pc has been running fine up until last night when it randomly stopped and now I can’t even boot my computer up for more than a few minutes before it shuts off again

The errors I have gotten so far : Memory_Management DPC_Watchdog_Violation Kernel_Security_Check IQRL_Not_Less_Or_Equal SYSTEM_SERVICE_EXCEPTION

submitted by /u/Bimmybim
[link] [comments]

:)

 

Startup Blue Screen

Hi Jon,

Startup blue screen error(s) can occur if a problem causes your PC to shut down or restart unexpectedly. It could be due to the following:

• Outdated device software drivers
• Corrupted Windows update system files
• Software/Security conflicts

We would like to know some information:

• Did you get any blue screen stop error codes?
• Have you tried booting in Safe mode?

We suggest that you check this
article about troubleshooting blue screen errors and follow the troubleshooting steps provided there.

We will wait for your response

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.

 

Blue screen error

Hi,



Thank you for writing to Microsoft Community Forums.



I understand that you are getting a Blue Screen error on your computer. I’ll certainly help you with the issue.



However, please let us know:

• What is the complete Blue Screen error message you receive?
  
• Are you aware of any changes made to the computer prior to the issue?
  
• Are you able to boot the computer to desktop?
  

I would suggest you to unplug all the external devices from the computer except mouse and keyboard and try to boot the computer.



If you are unable to boot the computer to the Desktop, I would suggest you toBoot your PC in Safe Mode: Try booting the PC to safe mode and check if it is still crashing. Refer the article
Start
your PC in safe mode in Windows 10



In case, the PC is working fine in Safe Mode then you may try performing Clean Boot and see if the PC boots normally. Refer the article
How
to perform a clean boot in Windows



Performing a clean boot will start the computer with minimal set of drivers and programs, to determine whether a background program is causing the issue. Some of the Startup programs will not load after performing a clean boot on the computer.
However, that functionality will return when you reset the computer to start normally after finishing the troubleshooting.



Note: Please refer the section
Reset the computer to start normally after clean boot troubleshooting to boot the computer in to normal mode after troubleshooting.



If the PC crashes after performing clean boot, I suggest you to perform hardware clean boot while in Safe Mode and check if that helps.



Hardware clean boot:



I suggest you to follow the steps mentioned below and disable the devices is Device Manager:

1. Press Windows key + R. This will open
   Run. Alternatively, you can go to Start and search for Run.
   
2. In Run dialog box, type devmgmt.msc and hit enter.
   
3. Now, expand Display adapters,
   Printers, Sound, video and game controllers one by one.
   
4. Right click on the devices inside the section and click on
   Disable device.
   
5. If asked for restart click on restart later and disable all the devices.
   
6. Close the device manager window and restart the computer.
   

You may also refer the steps mentioned in the article
Troubleshoot blue screen errors.



However, as Thagstrom has suggested, please share the dump files with us to get to the root cause of the issue.



Let us know how it goes.



Regards,

Nikhar Khare

Microsoft Community - Moderator