Windows 10: DISK PARTITIONS/CLEAN INSTALLATION OF WINDOWS

Hi everyone, I want to do a clean reinstall of windows 11 and I want to delete all data.I currently have two SSDs of 2TB each. In one SSD disk 0 I installed Windows, in the other disk 1 I installed games and various programs.A few days ago, in another support thread, I was told to delete all partitions on disk 0 and disk 1 when reinstalling, and then create space on disk 1 using disk management.https://answers.microsoft.com/en-us/windows/forum/all/clean-reinstall-of-windows-11-2h24/7b6208d0-7eef-40bf-8fa1-1350fa7ab01eSo I used the diskpart command in cmd to view the partitions I currently

:)

 

W7 Hard drive partition issue

to get rid of that 100 meg windows partition that setup creates for you on a new install on a blank hdd:

- press shift+f10 when on the partition management screen in setup <-- this opens a command prompt
- diskpart <-- start the windows command line partition management tool
- list disk <--- list the installed hdds in this computer for the next step
- select disk 0 <- might have to replace 0 with the number of the correct disk
- clean <-- this will erase all data on the disk you selected one step up- dont use the wrong disk!
- create partition primary <- creates a primary partition taking up all space on the drive, adjust the command if necessary
- exit, exit to exit diskpart and the command prompt
- click refresh in partition manager and select your newly created partition and install to that

 

Clean Install Windows 10 partition issue

Hello,

Thank you for writing to Microsoft Community Forums.

I appreciate the troubleshooting steps performed to resolve the issue. However, let’s try with the further troubleshooting steps and see if it works. Initially, I would suggest you to create a bootable media with a USB/Flash drive of capacity 8GB.
For better understanding, you may watch the video with the procedure from the article on
How to Clean Install Windows 10 on a PC Step-by-Step
Guide.

Set the boot priority to USB once after creating a bootable media using a USB and proceed with the Windows Installation. On the drive selection window, press Shift + F10 keys to open the Command Prompt. Then follow the steps listed
below:

• Type the following command in the Command Prompt window and press Enter:
  diskpart
  
• Once after executing the above command, type the following command to list the current drives and press Enter:
  list disk
  
• List disk will give you the list of drives, use the following command to select the drive and press Enter: select disk 0
  
• Type the following command to check if the disk is online: online disk
  (if the disk is not online)
  
• Type the following command to clean the drive and press Enter:
  clean
  
• To create a partition, type the following command and press Enter:
  create partition primary
  
• To select the partition that you created, type the following command and press Enter:
  select partition 1
  
• To set the partition active, type the following command and press Enter:
  active (if this is the boot partition)
  
• Type the following command to assign a drive letter and press Enter:
  assign letter(letter)
  

• After completing all this, close the command prompt screen and click on
  refresh button.
  
• Then you will only have one drive with “unallocated space”, just select the partition to start the installation.
  

Let us know how it goes and I look forward to hearing from you soon.

Regards,

Mala S

Microsoft Community - Moderator

 

Installing Windows Vista/7 on a GUID Partition Table

I've never tried multiple partitions so this is a shot in the dark...

At step #10, I would try setting the size parameter (it is in mebibytes) to how large you want the partition windows is installed on to be, then go ahead and install windows. This will leave the rest of the drive raw instead of consuming it into the OS partition (C drive). Once you successfully boot into Windows, you should be able to use Computer Management -> Disk Management to create partitions in the raw space.


If you really wanted to do it with diskpart before Windows is installed, you basically repeat the following lines making sure to specify a size if you don't want it to consume all remaining space:

• create partition primary size=size in mebibytes here
• format quick fs=ntfs label="appropriate name here"
• assign letter=C thru Z here

Obviously, you can use quick formatting or leave it out for full format. Leave off the size parameter when you reach the final partition that should consume all the remaining space. Also remember that the order you do this in goes from the outside of the disk (where it is fastest) to the inside of the disk (where it is slowest). Because of this, it is recommended to put EFI (e.g. size=300), then MSR (e.g. size=300), then Windows (e.g. size=30000), then Applications (e.g. size=70000), then Storage (e.g. no size parameter).

If I'm right, the above example would look like this:

• diskpart
• list disk
• select disk <id>
• online disk
• attributes disk clear readonly
• clean
• convert gpt
  
• create partition efi size=300
  
• create partition msr size=300
  
• create partition primary size=30000
• format fs=ntfs label="Windows"
• assign letter=C
  
• create partition primary size=70000
• format fs=ntfs label="Applications"
• assign letter=D
  
• create partition primary
• format fs=ntfs label="Storage"
• assign letter=E
• exit