Windows 10: Enabling Bluetooth audio device

I've been trying all day to figure out why my JBL flip 6 wont play sound out of it when connected to my pc its worked before but now it wont show up in playback devices and its set to don't allow apps and windows to use this device and when I click allow it doesn't do anything. I swear I've tried every solution and nothing has worked.

:)

 

Re-enable audio device

Hi,

I would be happy to assist you.

Before we proceed with troubleshooting, I would need little information on the issue.

• Are using speakers / head phones to listen to audio?

If you have disabled the audio device, then you might not see it under the list of playback devices. I would suggest you to follow these steps to make sure you see the disabled devices:

• • 
    Open
    Control panel.
    
  • 
    Click Hardware and Sound and then Click on
    Sounds.
    
  • 
    Under Playback tab, right click on the empty area and make sure
    “Show Disabled Devices” has a check mark on it. If headphones/Speakers are disabled, it will now show up in the list.
    
  • 
    Right click on the device and
    Enable it. Click OK.
    

If the issue still persists, try enabling speakers automatically using steps below.

• 
  Go to Settings> Click on themes> Advance sound settings> right click on the speakers or the audio device youo have connected > click on
  Configure device.
  
• 
  Test the sound level you want, click Next.
  
• 
  And configure the audio devices.
  

Hope this helps you. Do reply if you need further assistance on Windows 10.

Thank you.

 

Cannot connect to Bluetooth audio devices (only) under 21H1.

I had no problem connecting Bluetooth audio devices while running Windows version 20H2, and had 3 different audio devices paired and working normally. Upon upgrading to the latest Windows 10 version (21H1, 19043.1348), they can no longer connect.

There's nothing wrong with the devices. My 2nd system is running 20H2 and is connecting fine with them.

On my primary system running 21H1, I go to the Bluetooth settings screen, see my paired devices in the list. I turn on a Bluetooth audio device... and nothing happens. Previously the laptop would auto-detect the audio device and I'd be good to go. So I select the paired audio device in the list, see the option button to "CONNECT" and press it. IMMEDIATELY, I'm given this message: "That didn't work. Make sure your bluetooth device is discoverable." It's obvious it's not even trying. It's an instant response. On my 20H2 laptop, when I try to manually connect to a Bluetooth audio device that's not turned on, it takes about 20 seconds or so until the "didn't work" message to appear. It's clearly trying.

NOTE: I have a mouse device connected via Bluetooth and it's working perfectly fine. It's only audio devices that fail.

Another vexing related issue -- if I try to remove any of my Bluetooth audio devices from the paired list, I get a "Remove Failed" message and nothing happens.

Troubleshooting: Went to Devices --> Bluetooth. Did a View of hidden devices... and yes, there were duplicates of these devices listed. I deleted all of them. I rebooted and while they are absent from the Devices list, they're still showing up in the Bluetooth interface and behaving as before. I ran the Bluetooth troubleshooter that claimed to find a problem and fixed it, but rebooting showed that not to be the case.

Either something appears to be wrong with 21H1, or I have some screwy configuration conflict going on.. I've got Realtek Bluetooth hardware. I have uninstalled Bluetooth and reinstalled the Realtek drivers. No help. Upgrading to 21H1 was long and tedious--I don't want to roll back to 20H2. Is there anything I can try to fix this?

Thanks!

 

Bluetooth Paired but not listed on Select playback device..

Do they work if you connect them through BT with your cellphone or tablet? Google is your friend. Try the following. https://support.microsoft.com/en-us/...&v4h=winxptab1 Uninstall the driver that you installed. Windows 10 should load the correct driver when you plug the dongle into the computer. Check if the following settings for the Bluetooth speaker is enabled by default. If not, let’s enable it and check if it solves the issue.

You can follow the steps to enable the Bluetooth audio service:

a) Press Windows key + X key together and select Control Panel from the list.

b) Click on Hardware and Sound and select Devices and Printers.

c) In Devices and Printers, locate Bluetooth speaker device and Right Click on the device.

d) Click on Properties and navigate to Services tab.

e) Select “Audio Sink”, "Hands free Telephony" and "Remote Control".

f) Click on Apply.