Windows 10: Error 4-1,my pc says i dont have usc 3.0 ports even tho i have one

So i recently got a HP windows mixed reality headset and i've faced an issue when plugging the headset in.Before plugging the headset i've done the compality test and everything was good.After plugging my headset into my pc,the test says that my pc cannot run the mixed reality as i am missing usb 3.0 ports,wich is not the case as my pc only has usb 3.0 ports.If i skip the compability test and plug the headset in,i get the error 4-1.I am completely clueless on what could provoke this error,if anyone could help me i'd really appreciate it.Another detail : when i plug the cables in my pc,they sta

:)

 

Repeated Crashes and Boot Errors Apparently Caused by Driver Updates

The chkdsk /f /r report displayed that there were corrections made in the volume bitmap.

Run these commands and post images and then continue with the prior steps:
There was a command for disk 1 but the command for disk 0 seems to have been skipped (steps 24 and 25) for the partition information. These are some additional commands.

1) diskpart
2) list disk
3) select disk 0
4) list volume
5) list partition
6) select partition 1
7) detail partition
8) select partition 2
9) detail partition
10) select partition 3
11) detail partition
12) select partition 4
13) detail partition
14) if there are any other partitions on disk 0 continue in the same fashion
15) exit
16) continue with prior steps

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

 

Problem updating Windows Surface Pro 4 with Windows 10 feature updates

Hi,

I have manage to install image for Microsoft Surface Pro 4 by going to https://support.microsoft.com/en-us/...erecoveryimage and download a recovery image for Microsoft Surface Pro 4.

What I did to reset your Surface from a USB recovery drive was:
Step 1: Make sure your Surface is turned off and plugged in (hold down the power
button for 30 seconds).
Step 2: Insert the USB recovery drive into the USB port on your Surface.
Step 3: Press and hold the volume-down button while you press and release the
power button on your Surface.
Step 4: When the Surface logo appears, release the volume button.
Step 5: When prompted, select the language and keyboard layout you want.
Step 6: Select Troubleshoot > Reset your PC.
If prompted for a recovery key, select Skip this drive at the bottom of the
screen.
Step 7: Select the target operating system you wish to reset. This
refers to the current operating system installed on your Surface.
Step 8: Select Yes, repartition the drives, and on the next page, select Next.
Step 9: Choose Just remove my files.
Step 10: Select Reset.
Surface restarts and the Surface logo displays while the reset process continues
(this can take a while).

This always fails and I have to do the below which continues installation.
Windows 10 Installation Media:

1. Insert the Media (DVD/USB) in your PC and restart.
2. Boot from the media.
3. Select Repair Your Computer.

Select Troubleshoot.

1. Choose Command Prompt from the menu:

Type in the command:
Diskpart
Type in the command:
List disk (Note which disk is your Boot drive number mine is 0)
Type in the command:
Sel disk 0
Type in the command:
List vol (Note which volume is the EFI partition mine is 4)
Type in the command:
Sel vol 4
Type in the command:
assign letter=V:
Type in the command:
Exit
Type in the command:
V:
After you have assigned a drive letter Using Diskpart You can format the EFI partition:
Example: if you assigned a letter V to the partition the command would be:
format V: /FS:FAT32
Type in the command:
bcdboot C:\windows /s V: /f UEFI


Now I have an issue that I cannot install Feature Updates. They keep failing to install.
Any ideas how to resolve issue?