Windows 10: Ethernet and Wifi Adapter freeze

So I have a brand new computer 1 week I just built with an asus rog z790 maximus hero running Windows 11. I started noticing that the internet will just go out occasionally and I can not get back without a reboot, I have it wired to my 2.5g switch which is working fine as nothing else goes offline. When this happens I have tried resetting my "IntelR Ethernet Controller I226-V" adapter which just freezes, enable/disable doesn't work, uninstall doesn't work, updating drivers doesn't work. After it goes out I thought I'd try the Wifi which also doesn't work, it just sticks on "identifying" an

:)

 

IP configuration not valid - interference from ethernet adapter?

Solution 1: No Internet Access In Windows 8.1or Windows 10

Step 1:

Go to Device Manager → Network adapters.
Step 2:

Expand it (Network adapters).


Step 3:

Select your network adapter


Step 4:

Right click on your wireless network adapter or Ethernet adapter and then tap “Update Driver Software”.
(in this case your network adopter is Ethernet adopter so tap your Ethernet adapter)
Step 5:

Now on a new window you will need to click on “Browse my computer for driver software”.




Step 6:

Then select “Let me pick from a list of device drivers on my computer”.



Step 7:

Now choose the “Manufacturer’s drivers” from the list of two and then click next.



Step 8:

After the completion of the process just restart your PC and check if the problem is solved or not. If not, goto solution 2.



Solution 2: No Internet Access In Windows 8.1,windows10

Step 1:

Open command prompt.
Step 2:

Just go on hitting the enter after typing the each command.
netsh int tcp set heuristics disabled
netsh int tcp set global autotuninglevel=disable
netsh int tcp set global rss=enabled
Step 3:

Now to check if the settings are disabled type:
netsh int tcp show global
then hit enter.
Step 4:

Now the thing left is just rebooting your system and just check if the problem is solved or not and just give feedback.*chuckle*Thumbs

 

enable ethernet / fix wifi adapter

how to enable ethernet adapter I don't see it in the network adapter list it was there when I disabled it.

Also my net freezes every 10 minutes saying the gateway is not accessible It's doing it on both of my computers.HELP!!

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?