Windows 10: Floppy disk drive on Windows 10

I recently bought bought a floppy drive off Amazon along with some diskettes, but when trying to format the drive it gives me an error saying "Windows was unable to complete the format". Does anyone have a fix for this?

:)

 

Floppy disk drive driver

Greetings,

I appreciate your swift response, if the above steps did not work no worries since this is an open forum , we can ask assistance from other community volunteers with their feedback and suggestion with this issue.

For the meantime you can try to check on this thread by @Gary_816

https://answers.microsoft.com/en-us/windows/for...

After 6 hours this worked for me. I have the Teac drive also and it appeared to install correctly, but did not show up in Windows Explorer. During a boot up the drive clicks and spins like 3.5" drives did on older systems if there is diskette in the drive.
I opened "Devices and Printers" in the Control Panel and the drive was there. With the diskette still inserted, right click on the Teac icon and select "Browse files > Floppy Disk Drive (A". File Explorer should open up and you will see the files on the
floppy listed. You will now see "Floppy Disk Drive (A" listed under "This PC". Right click on "Floppy Disk Drive (A" and select "Pin to Quick access". "Floppy Disk Drive (A" should appear under "Quick access". Although "Floppy Disk Drive (A" will disappear
from "This PC" after you close and reopen File Explorer, it will remain under "Quick access" and you can access it from there. It appears that W10 now thinks there is an internal drive "(A" because if you right click it "Eject" does not appear as an option.
Why it disappears from "This PC" is a mystery.

Note: On my machine (ASUS) if I take out the diskette or disconnect the drive, "Floppy Disk Drive (A" stays in the "Quick access" menu. So no need to keep a diskette in the drive all the time or even have it connected all the time. Worked fine after I reconnected
it.

Note 1: Under "Devices and Printers" the Drive was identified as "TEAC FD-05PUB". If you get something different (assuming you have a TEAC) try running "Troubleshoot" and see if that corrects it.

I hope the information above helps.

Have a wonderful day ahead and stay safe.

With Warm Regards,

 

Windows 98 phantom floppy drive preventing real floppy drive from functioning

Here try this

Safe Mode

Start Windows in Safe mode and try to access the floppy disk drive. To start Windows 95 in Safe mode, restart your computer, press the F8 key when you see the "Starting Windows 95" message, and then choose Safe Mode from the Startup menu. To start Windows 98 in Safe mode, restart your computer, press and hold down the CTRL key after your computer completes the Power On Self Test (POST), and then choose Safe Mode from the Startup menu.

If you can access the floppy disk drive, follow these steps:

Use the right mouse button to click My Computer, then click Properties on the menu that appears.
Click the Device Manager tab.
Double-click Floppy Disk Controllers.
Click the floppy disk controller for the drive you are having problems with, then click Properties.
In Windows 95, click the Original Configuration (Current) check box to clear it. In Windows 98, click the Disable In This Hardware Profile check box to select it. This disables the Windows protected-mode driver for the floppy disk drive controller.
Click OK.

Restart Windows normally.


If you can access the floppy disk drive successfully after following the above steps, the following conditions may be true:
The floppy disk drive controller may not be supported in protected mode.
There are drivers loading in the Config.sys or AUTOEXEC.BAT file that may be necessary for protected-mode access.
There are drivers loading in the CONFIG.SYS or AUTOEXEC.BAT file that may be causing conflicts in Windows and need to be disabled.

If you still cannot access the floppy disk drive after following steps 1-7, follow these steps:

Use the right mouse button to click My Computer, then click Properties on the menu that appears.
Click the Device Manager tab.
Double-click Floppy Disk Controllers.
Click the floppy disk controller, and then click Remove to remove the controller.
Click OK.
In Control Panel, double-click Add New Hardware.
Click Next, and then click Yes to allow Windows to detect the hardware in your computer.
When the Add New Hardware Wizard is finished, restart the computer and try to access the floppy disk drive again.
Redetecting the floppy disk controller should resolve any addressing problems with the controller by detecting the correct address range. If the floppy disk controller is not detected correctly, there may be a problem with the floppy disk controller. If the floppy disk controller is redetected but you still cannot access the floppy disk drive, there may be a problem with the floppy disk.

 

Floppy Disk Drive (A

Hi Penny,

Thank you for posting on Microsoft Community.

We are really sorry to say that the Floppy Disk Drive has no compatibility with Windows and there is no support to floppy disk drives.

For further more clarifications I would suggest you to check/Contact with the manufacturer.

keep us posted if you are facing any other issue with Windows.