Windows 10: Fresh install Windows 11 on tablet PC : no USB or network after reboot

I'm installing Windows 11 from a bootable USB on a tablet PC, and for some reason it loses access to all USB devices and all network devices after booting into the freshly installed Windows 11 image on the hard drive. If I reboot from the USB, all the drivers are available and working, but only within the little installer. No matter how I do the transition to the Windows 11 desktop, it gets stuck saying "A network connection is required to continue configuring Windows..." At that point, I can't even install drivers from the USB, because all the USB devices and ports are no longer recognized. S

:)

 

ST5022 Tablet Windows Tablet/Linux USB Install

I have recently been trying new OS's for my tablet PC and thought i'd share the aquired knowlage for reference by others and probably me again at some point,lol

Ubuntu :
This operating system was very easy to install via my USB drive, with downloads freely avalable for USB install, but it took a little fiddling to get the stylus to work. I took my main set up guide from this site to configure my tablet and stylus for Ubuntu. After i had installed the wacom drivers i found a small error when editing the xorg.conf file in the terminal which i have rectified below:

Section "InputDevice" # the three Wacom serial devices for the screen...
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/ttyS0"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4"
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/ttyS0"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4"
EndSection

Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/ttyS0"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4"
EndSection

Section "ServerLayout"
Identifier "normallayout"
InputDevice "Stylus" "SendCoreEvents"
InputDevice "Eraser" "SendCoreEvents"
InputDevice "Cursor" "SendCoreEvents"
Option "Clone" "on"
Option "AllowMouseOpenFail" "on"
Option "Xinerama" "off"
Screen "Default screen"
EndSection

was set to "touchscreen" which was an unknown device

Ubuntu worked well amd had some good apps but i abandoned it for a few reasons :

• no support for pc's fingerprint recognition (Thinkfinger did'nt support it)
• Stylus did'nt work with virtualbox properly
• Unsuported industry level design tools (winedoor options too limiting)
• unable to config inboard keyboard for password entry

Windows Tablet PC:

Getting this Os to run from USB can be a nightmare but i found it relativly simple this way:

• Download HP USB Disk Storage Format Tool
• Download PeToUSB or usb_prep8.zip
• Download Windows.iso or insert Windows disk

• Insert USB
• Format USB with HP USB Disk Storage Format Tool or PeToUSB (FAT files, Basic Format)
• Intert windows CD or load .iso file (magiciso, power.iso etc)
• open usb_prep8.cmd and press enter to go to copy menu
• enter 1, then enter drive letter that windows cd or image is on, enter again
• enter 3, then enter usb drive letter, enter again
• enter 4 and follow onscreen prompts
• Install OS by entering 1>txt setup then 2>visual setup, following onscreen guides
• keep USB untill after fist startup and load of windows

I had a problum with the PC unable to boot without USB untill i changed the BOOT.ini file on the system. in C:\windows like this

[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /noexecute=optin /fastdetect

these values where set to 1 for the USB boot

Aside from that I've had no problems so far with the Windows OS

 

Fresh USB Windows 10 Install - Failing

I am trying to install a fresh copy (reformatted the hard disk) of windows 10 using a USB

• Created an installation media on a USB flash drive (Win 10 pro) from this page https://www.microsoft.com/en-us/software-download/windows10
• Changed the boot order on the other PC so that it boots using USB
• Selected custom install
• Installing Windows goes through the following steps successfully: Copying Windows Files, Getting Files ready for installation, Installing features, Installing updates and before the last step (Finishing up), it restarts
• Then it goes back to the start of the installation steps

I am stuck and have read numerous posts but don't know what to do to install a fresh copy of Win 10.

 

fresh install of windows 10 on tablet

and just to get things right. here are the steps that i make when instaling....