Windows 10: hi i have a problem evry day after my pc was closed for like 8 10 hours when i boot it...

Here is the content of the minidump folder form today, in case someone can help me. i think i have 5 more dumps from provious days so let me know if you need those as well. Thanks in advance!************* Preparing the environment for Debugger Extensions Gallery repositories ************** ExtensionRepository : Implicit UseExperimentalFeatureForNugetShare : true AllowNugetExeUpdate : true NonInteractiveNuget : true AllowNugetMSCredentialProviderInstall : true AllowParallelInitializationOfLocalRepositories : true EnableRedirectToChakraJsProvider : false -- Conf

:)

 

Windows 10 computer takes hours and sometimes days to boot

You may have a device that is hanging up your system, causing the long boot up time. Suggest going to a bare bones configuration by doing the following:

1. Draw a picture of your back panel showing all of the ports. Indicate what is plugged into which port so you can return to normal later. Do this for the ports on the front and top too.

2. Power off your PC, disconnect the a/c power cable from the back, then press the power on button for 5 seconds to discharge capacitors which removes residual power to the motherboard.

3. Remove every cable from your PC except ones for the keyboard, mouse and monitor.

4. Open the cover for your PC. Then touch the bare chassis with both hands to discharge any static electricity from your body. Then disconnect the SATA and power cables from your optical drive.

5. If you have more than one hard drive in your PC, disconnect them too. You should only have your system hard drive (or SSD) connected at this time.

6. You should be in a bare bones configuration now.

7. Power on your PC and see if it boots up normally.

8. If it still does not boot up normally, power off as in step-2 again. And discharge your self as in step-4.

9. I assume you have two RAM cards of 4GB each for 8GB. If so, determine which slot is slot zero and remove the other RAM card. Slot zero is usually the once closer to the CPU. Be sure you draw a picture (or take a picture with your camera) so you know which slots the cards are in if your motherboard has 4 RAM slots. BE SURE YOU DISCHARGE ANY STATIC ELECTRICITY BY DOING STEP-4 before handling RAM cards. Try to handle only by the edges and not touch the circuits as much as possible.

10. See if it boots up normally. If not, remove the one RAM card (you only have one RAM card installed) and replace it with the other RAM card. You should still have only one RAM card installed.

11. See if it boots up normally.

Note that a defective Optical drive or defective additional hard drives are very likely suspects as cause for long boot times, due to firmware or software waiting for the device to get ready. There should be a time out to not last days but strange things can happen.

My $.02,

 

laptop doesnt boot automatically

This is what happened.

1. Did a repair install and later disabled hibertnate in CMD.
2. Enabled legacy option ROM in BIOS.
3. After a few times startup ( i used the system in such mode for 5 days), changed boot option back to default.
4. Vola!! It boots automatically to win10 without any keypress. Tested it with many starts to confirm the same.
5. Re-enabled hibernate option using CMD and later selected Fast Startup.
6. System booted normally, without the need for any keypress.

I do not know exactly whether such steps resolved the problem or what else happened, hence cannot suggest above steps.

Many thanks to all members who helped to troubleshoot problems.

 

HIS IceQ turbo overclocking problems

If Your Card is Like my HIS 2600 Pro, they probably OC'd it at the factory and then locked the frequency's so catalyst can't adjust them.

Riva Tuner v2.08 will let you adjust the clock/Mem/Fans

I suggest slowly stepping the core or mem one at a time till it won't go any further, then subtract about 10+ mhz from each (for stability), set the clocks and run stability tests.