Windows 10: How do I fix there was a problem resetting your pc

I had a problem where windows couldn't repair my PC. I needed to factory reset the PC through the bluescreen since I couldn't access the desktop. I went to advanced settings and troubleshoot where I pressed the reset PC button and clicked remove everything then a message popped up saying there was a problem resetting your PC.


Any solutions will be greatly appreciated.

:)

 

Factory Reset Windows10: There was a problem resetting your PC FIX


How to Factory Reset Windows10 or upgraded to Windows10 from Windows7 or 8.
This is also a FIX for the ERROR: There was a problem resetting your PC.
This fix is only for Legit Authorized Copies of Windows 7, 8, or 10.


Hey all, I upgraded to Win10 from Win8.1 when it was released for free upgrades in 2015. It is now 2016 and I wanted to Factory Reset my PC so I can start fresh again. I attempted to do it from Settings/Update and Security/Recovery/Reset this PC as suggested by Microsoft but I received and error saying "There was a problem resetting your PC. No changes were made." After searching the web I found many different fixes but they all seems so involved. Making a boot flash drive or burning a DVD and use their software... There is an awesome tutorial on this forum called Windows 10 Clean Install but I like to KISS when I can (Keep It Simple Stupid) so I decided to check with Microsoft.com before I started that process.


THE SIMPLE FIX I FOUND THAT WORKED FOR ME:
Go to: Windows 10
Click the "Upgrade Now" button.
Follow the prompts and you're good to go.
Works with Windows 7, 8 and 10. Simple enough for me

I wasn't able to find this simple suggestion when searching the web so I felt I should post it in hopes it helps someone too

-

 

router logs DoS attack from a local PC....

Well you did not say that you don't really know what you are doing. It's not a problem of course, but it changes things a little.

It's not even clear if the PC or the router is the problem at this time, so I suggested that you disable some unnecessary things which are usually known to cause many problems, sorry if those were too complicated.

• You could reset some network related stuffz on the PC as a next step. Open an elevated command prompt (run as administrator), and enter the followings on the PC:
  netsh int ip reset reset.log
  netsh int ipv6 reset
  netsh winsock reset
  netsh branchcache reset
  netsh advfirewall reset
  (note: You can export your current firewall rules in the "group policy" before the reset if it's needed for some reason)
  
  
• Btw, Would it be a problem to reset the router to the default settings if the things we are trying will not help? There is a menu point for that called "factory settings" (and also a little hole on the back if you prefer that one).. the Administrator username in the router after the reset would be admin and the password is probably on a sticker at the bottom of the router (special settings needed to go online with your ISP might be also necessary)
  This is not needed now (not yet), but perhaps the source of the problem is at the router and not the PC in question, so we may come to that eventually.

ps.: Do you have a second network card you could test in that PC and a different cable to rule out some hardware issues on the PC side?

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".