Windows 10: How do I put my drives back to the way they were before OR what is best practice for disk...

I just used Samsung Migration Magician. When I restarted the computer after finally replacing the HDD with my SSD physically, I got an error about to not remove my USB (Windows on the Go). I never used Window on the GO. The thing is I actually used a USB to SATA cable first and this was obviously disconnected since the SSD was able to boot up my computer. The reason why I was able to clone over my OS. I have a picture below of my current Disk Management and everything seems to be working fine, but it doesn't have the D: drive which had the WIN10 Recovery since I bought the laptop back in 2016 (P1A78UA#ABA, HP Pavilion) and the last time I had a computer before that was around 2009. How do I get that drive (D added since I was under the impression it would be available just like the C: drive. I did a 1 to 1 swap for the same size (1 TB) those two drive would be as is when the computer booted up. Thank you for the support.


Screenshot of Current Disk Management:



:)

 

How to Partiton a Hard Drive in Vista

This is a way to get Vista to see another hard drive that is not associated with the OS. There is some times when your new hdd doesn't seem to want to work well with Vista. But, there is a solution in it.

Open the Computer Management By doing these steps.

• Click on the Start Button
• Click on Control Panel
• Click Administrative Tools
• Double click on Computer Management

You are now in the Navigation panel of the Computer Management.
When in Computer Management, you then have to allow the new drive to be recognized.

• Double click on Storage
• Double click on Disk Management

Now in the middle of your screen there is the layout of the Disk Drives that you have. The drives that are partitioned will show by the drive lettering. The others will just show up as having nothing at all in them. Below that there will be the Disk drives that are installed into the computer. You'll see that the primary one will all ways read as "Disk 0". Then you will have Disk 1 and so on. Under the Disks there will also see your CD-Rom drives.. If there is more then one, it will be labeled the same as Disk drives..

On to the Partitioning of the drive in question.

• Right Click on the drive
• Click to format the drive or Enable Volume. There will be a series of windows that open up. This is Vista's formatting. Just go threw the windows, and make sure everything is the way you want it to happen.
• Once the formatting is done, will take some time depending on the drive size.
• Right click on the drive
• Click on Mark the Partition as Active

After you have done those steps, The drive will be up and running threw Vista.



:Side Notes:
If you are not the Administer to the Os, then you will have to enable it..
You may also want to redo the drive lettering of it all. But, I really don't see a reason to do so. If you do, you have to redo drive paths and so forth.. A lot of work on something so small...

 

HP Disk Drive not visible

Hi,

Thank you for posting your query on Microsoft community.

I would suggest you follow the steps below and see if it helps:

Method 1: I would suggest you first try the Troubleshooter.

Please follow the steps below:

• 
  Type “Troubleshooting” on the Windows Search bar and hit enter.
  
• 
  On the left side of the Troubleshooting window, click on “View all”
  
• 
  Click on Hardware and Devices. Please provide a password if asked for it and click ok.
  

Method 2:

• 
  Press Windows key + X key and click Device Manager.
  
• 
  Expand the Sound, Video and game controllers.
  
• 
  Right-click on the Disk Drives and click on Properties.
  
• 
  Go to the Drivers Tab and Click Enable (If not enabled).
  
• 
  Restart the computer and check.
  

Hope this helps. Please reply if you have further related queries.

Regards,

 

Malfunction of 3.5" disk drive in Windows 10.

Hi,





To assist on your disk drive issue, please clarify the following:

• 
  Did you get an error message when the disk drive refused to read the inserted disk?
  
• 
  Have you tried updating the disk drive's driver?
  
• 
  What
  other troubleshooting steps have you done so far?
  

Regards.