Windows 10: How to fix hard drive so this message won't appear every time I turn on my PC: "Fixing C:...

Yesterday my PC fell a couple of inches while booting I had it leaning against a wall and it slipped and it froze. I rebooted it and saw the message in the title different numbers of course. It took a couple of minutes but after it finished the computer was working as usual. However, today the message appeared again.

It's still working fine after the fixing sequence finished, but is it going to keep happening every time I turn on my PC? Is there something I should do before turning it off to avoid any more damage to the hard drive?

:)

 

Gigabyte motherboard, pc won't bootup after recent hard drive change

So I've previously had this problem when I added new SATA hard drives to an old one, all I had to do was switch hard disk priority to the one I wanted to boot from. But that's not working right now.

Error message: AMD Data Change...Update New Data to DMI!
Specs:

• Motherboard: Gigabyte ma785gmt-ud2h
• Four SATA hard drives, three 2tb and one 1tb
• One IDE hard drive, 160gb
• 6gb RAM
• Everything else is the default

What happened: I had an Amahi home server running on this PC with Ubuntu 12.04LTS as the OS. It was using the four SATA hard drives and everything was running smoothly. Then I read that it's easiest to have a setup where the OS/Amahi is installed on one small hard drive while the large hard drives are used to keep the files on, this makes it easy to update the OS without worrying about the files. So today I installed Ubuntu 12.04LTS on an old IDE 160gb hard drive that I had laying around, which would be perfect to use since there is exactly one IDE port on the motherboard.

I disconnected all hard drives, connected the IDE, installed Ubuntu, and rebooted. I got a "AMD Data Change...Update New Data to DMI!" message.

What I tried:

• Have the IDE be given priority over other hard drives.
• Connecting all the hard drives back, with and without the IDE hard drive. Same message.
• Disconnect all hard drives, connect IDE, and set BIO to opimised defaults. Same message.
• Disconnect CD drive with only IDE attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with only SATA attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with SATA and IDE attached, same message. Reconnect CD drive, same message.
• Just IDE connected, mess with the peripheral settings by changing "OnChip SATA Type" to ATHCI, RAID, or IDE. Tried this with "As SATA Type" and with "IDE" set for the port4/5 type
• Just IDE connected, disable SATA controller
• Disconnect IDE, reconnect original hard drives. I still get the same DMI message.
• Attempt to boot from the SATA hard drive that has Ubuntu on it, using each of the SATA ports.
• Update BIOS to F10B, disabling the "Remember DMI" option. I reconnected all hard drives and the CD drive (the pdf said the 'system' will redetect all devices). Now I got the "AMD Data Change...Update New Data to DMI! Update Success" message, still hanging there. Rebooted, now it's the original message.

So I am at a loss. Any suggestions?

Edit: there were many suggestions to try clear the CMOS, however that didn't seem to help the posters. I haven't tried that, but if people suggest I should then I will do so tomorrow.

 

Startup problems. Autorepair won´t fix it.

Hello

For the past few months my PC has not been able to startup. Auto repair won´t fix the problem, but it gave me all the problemdetails.

StartupRepairOffline

Problemsignature 01: 6.1.7600.16385

Problemsignature 02: 6.1.7600.16385

Problemsignature 03: Unknown

problemsignature 04: 211995523

problemsignature 05: AutoFailover

Problemsignature 06: 17

Problemsignature 07: NoRootCause

OS-version: 6.1.7601.2.1.0.256.1

local ID: 1030

Can anybody help me with this problem?

 

Gigabyte motherboard, pc won't bootup after recent hard drive change

now it look like it freeze because its searching boot sector...leave it there see if you have keyboard. and try booting in menu with only 1 pre formated hd on anjy port.


Your bios also as some kind of dual bios design a think... may cause problem or not. when problem like that append on integrated RAID controller, reset your bios by unplugging PC remove side cover. press power see led coming on then of really fast, if no this good too, no power on motherboard, remove cr2032 battery, then put jumper in reset position like short pin 2,3. (check if it output 2.8 to 3.0 volts if under change it), put back cmos battery , now unshort cmos jumper back to original position. plug power . boot, ERRoR about bioa , configure raid and check