Windows 10: How to fix the WiFi adapter so that it starts working properly

How to fix this problem and make it work properly

:)

 

I keep losing my WiFi adapter

I tried the Option 2 approach but kept getting the Error NetSetupDeleteObjecton Network Adapter error (0x80070005) error, even after a dozen executions of the command. That seemed like it was going nowhere so I tried Option 1. After completing the reboot in Option 1, I never got the dialog that asked if I wanted to make the computer discoverable, even after a significant wait. Do you have any further suggestions? I'm going to move on to "Compumind's" suggestion in the meantime and see if that helps.... - - - Updated - - -

I started working my way down the list.

1. Both the ipv4 and ipv6 resets said "access denied!". However, the mere attempt worked *briefly*, then the WiFi went down again.
2. I disabled and re-enabled the network adapter. Again, it worked *briefly*, then I lost the WiFi again.
3. I tried to disable the antivirus but couldn't find a setting for that so uninstalled it entirely. I got the WiFi back and this time it stayed on for several hours instead of a few minutes so I assumed it was fixed. Then I installed the new Avast One and the WiFi is still working so I'm assuming that all is well finally!

Thank you for this list of suggestions!!!

 

My wifi is not working properly

Hi Boralb, I'm Graeme, an independent adviser here to help.

Firstly, I would see if the troubleshooter fixes the issue. Click Start and type "troubleshoot" then select the first result. Scroll down and choose Internet Connection, and the troubleshooter may be able to automatically fix the WiFi issue.

If that doesn't help, try reinstalling your WiFi adapter manually. Here are the steps:

- Press Windows Key+X and choose Device Manager.

- Find your WiFi adapter in the list.

- Right-click it and choose Update Driver.

- If that doesn't work, try uninstalling it and then scan for hardware changes to reinstall the driver.

Please let me know how you go and if needed I can provide further troubleshooting options! Thanks!

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?