Windows 10: I am facing blue screen error before i run msconfig and go to advance options and checked...

I am facing blue screen error before i run msconfig and go to advance options and checked the check box of maximum 4096 and enter apply and ok and restart the pc and after blue screen is showing and I am unable to open safe mode ,unable to reset window ans etc

:)

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.

 

Advanced Options - Automatic Repair - MSconfig SNAFU

Hey All,

So, I made the mistake of following a YouTuber's advice, jury-rigging a few msconfig settings, and now my computer won't boot properly. I'll spare you the extraneous details and just tell you what I did.

• Boot > advanced options > set maximum memory from 0 to 256 (STUPID, STUPID, STUPID)
  
• Applied the advanced boot settings.

Now, every time I boot up my PC, it brings me to a blue screen showing its collecting error info and then attempts to restart. During the restart, the PC prepares and automatic repair, diagnoses the PC and then shows a message saying that Windows 10 cannot
automatically repair the PC. It then provides me with the following advanced options:

• Reset PC
• System Restore (when i did this, I got an unspecified error: 0x80070002)
• System Image Recovery
• Startup Repair
• Command Prompt
• Startup Settings
• Go back to the previous build (didn't work)

Is there anyway I can reset the configuration via the Command Prompt? If so, how?

Thanks!

 

Error. Blue Screen

Hi,

In addition to the above mentioned solutions by Community members, I would like to add the following:

Before we proceed I would like you to answer the following question:

• 
  What is the make and model of your computer?
  
• 
  Did you make any changes prior to the issue?
  

The issue might occur due to Viruses, or something changing/deleting in Registry Files, a failure during Bootup, or a corrupt file which could be due to age of a computer or viruses or somebody tampering with files.

I suggest you to follow the step below:

Step

I suggest you to refer the article below and check if it helps:

Troubleshoot blue screen errors

Resolving Blue Screen errors in Windows - Microsoft Support

Please get back to us with updated status, we will be happy to assist you.