Windows 10: I cannot connect to wifi. I found out that I have virtual network adaptersVMware completely...

Help me pls

:)

 

How to permanently disable ms virtual wifi adapter

Hi,

You may permanently disable the Virtual Network Adapter and Virtual Wifi Adapter by deleting it completely from the Network and Sharing Center.

To do this, kindly follow the steps below:

• Press Windows key + X on your keyboard.
• Select Control Panel.
• Click Network and Internet.
• On the left-side, click Change adapter settings.
• Right click on the name of the adapter, then choose Delete.

Let us know how it goes.

 

How to connect to an existing wifi network?

As you suggested, I tried disabling the ethernet adapter and that caused wi-fi to connect, so the desktop wifi does work. Also, I accessed the router and changed the wireless network name (to wfCHS). Thanks!

However many problems are still unresolved:

My laptop behaves just as I want it to. Assuming the router has wifi turned on and the laptop has an ethernet connection, connection to the internet is by ethernet (no private network name), and the wi-fi connection is to my private network "wfCHS", but with no connection to the internet. (If I disconnect the ethernet cable, then wfCHS becomes connected to the internet and stays that way even if I reconnect the cable.) A directory listing shows both laptop and desktop under "Network". Great!

Things are rather different with the desktop. With Ethernet disabled, the desktop shows a wi-fi connection to the internet. Under Settings > Status it's called "wfCHS" but under Network Connections it's called wfCHS2. If I then re-enable the ethernet connection, the wifi connection stays enabled for a minute or two, then disconnects. Further, the ethernet connection is given the name wfCHS2 under both Status and Network Connections.

Why does the desktop give an (unwanted) name to the ethernet connection while the laptop doesn't?

Why does the desktop disconnect its wi-fi connection a minute or so after the ethernet connection is enabled, while the laptop doesn't?

Why does the desktop give two different names to the wifi connection, depending on whether it's viewed under Status or Network Connections, while the laptop doesn't?

Why does the laptop show the desktop under Network, while the desktop shows only itself?

Things are so convoluted that I'd be happy to start over. I've had the desktop "forget" the wi-fi connection as you suggested, then re-established it, but this hasn't helped. Can the ethernet connection also be "forgotten"?

Really appreciate the help you've given so far!

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?