Windows 10: I can't format my hard drive because I get an error message about the Y drive is missing....

I can't format my hard drive because I get an error message about the Y drive is missing. What do I do?

:)

 

Hard Drive formatting

I beg to differ!!!! DO NOT DO A QUICK FORMAT !!! Quick Formatting is fine for a floppy drive but not for an OS hard drive! My opinion and we can be ok with different opinions right ?

 

Gigabyte motherboard, pc won't bootup after recent hard drive change

So I've previously had this problem when I added new SATA hard drives to an old one, all I had to do was switch hard disk priority to the one I wanted to boot from. But that's not working right now.

Error message: AMD Data Change...Update New Data to DMI!
Specs:

• Motherboard: Gigabyte ma785gmt-ud2h
• Four SATA hard drives, three 2tb and one 1tb
• One IDE hard drive, 160gb
• 6gb RAM
• Everything else is the default

What happened: I had an Amahi home server running on this PC with Ubuntu 12.04LTS as the OS. It was using the four SATA hard drives and everything was running smoothly. Then I read that it's easiest to have a setup where the OS/Amahi is installed on one small hard drive while the large hard drives are used to keep the files on, this makes it easy to update the OS without worrying about the files. So today I installed Ubuntu 12.04LTS on an old IDE 160gb hard drive that I had laying around, which would be perfect to use since there is exactly one IDE port on the motherboard.

I disconnected all hard drives, connected the IDE, installed Ubuntu, and rebooted. I got a "AMD Data Change...Update New Data to DMI!" message.

What I tried:

• Have the IDE be given priority over other hard drives.
• Connecting all the hard drives back, with and without the IDE hard drive. Same message.
• Disconnect all hard drives, connect IDE, and set BIO to opimised defaults. Same message.
• Disconnect CD drive with only IDE attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with only SATA attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with SATA and IDE attached, same message. Reconnect CD drive, same message.
• Just IDE connected, mess with the peripheral settings by changing "OnChip SATA Type" to ATHCI, RAID, or IDE. Tried this with "As SATA Type" and with "IDE" set for the port4/5 type
• Just IDE connected, disable SATA controller
• Disconnect IDE, reconnect original hard drives. I still get the same DMI message.
• Attempt to boot from the SATA hard drive that has Ubuntu on it, using each of the SATA ports.
• Update BIOS to F10B, disabling the "Remember DMI" option. I reconnected all hard drives and the CD drive (the pdf said the 'system' will redetect all devices). Now I got the "AMD Data Change...Update New Data to DMI! Update Success" message, still hanging there. Rebooted, now it's the original message.

So I am at a loss. Any suggestions?

Edit: there were many suggestions to try clear the CMOS, however that didn't seem to help the posters. I haven't tried that, but if people suggest I should then I will do so tomorrow.

 

How to Partiton a Hard Drive in Vista

This is a way to get Vista to see another hard drive that is not associated with the OS. There is some times when your new hdd doesn't seem to want to work well with Vista. But, there is a solution in it.

Open the Computer Management By doing these steps.

• Click on the Start Button
• Click on Control Panel
• Click Administrative Tools
• Double click on Computer Management

You are now in the Navigation panel of the Computer Management.
When in Computer Management, you then have to allow the new drive to be recognized.

• Double click on Storage
• Double click on Disk Management

Now in the middle of your screen there is the layout of the Disk Drives that you have. The drives that are partitioned will show by the drive lettering. The others will just show up as having nothing at all in them. Below that there will be the Disk drives that are installed into the computer. You'll see that the primary one will all ways read as "Disk 0". Then you will have Disk 1 and so on. Under the Disks there will also see your CD-Rom drives.. If there is more then one, it will be labeled the same as Disk drives..

On to the Partitioning of the drive in question.

• Right Click on the drive
• Click to format the drive or Enable Volume. There will be a series of windows that open up. This is Vista's formatting. Just go threw the windows, and make sure everything is the way you want it to happen.
• Once the formatting is done, will take some time depending on the drive size.
• Right click on the drive
• Click on Mark the Partition as Active

After you have done those steps, The drive will be up and running threw Vista.



:Side Notes:
If you are not the Administer to the Os, then you will have to enable it..
You may also want to redo the drive lettering of it all. But, I really don't see a reason to do so. If you do, you have to redo drive paths and so forth.. A lot of work on something so small...