Windows 10: I have a Brother printer and used to be able to scan off it but now it won't scan. How do...

I have a Brother Printer and used to be able to scan. Now it won't scan. How do I get that function to work?

:)

 

Can't "Scan To" from printer. Please help!

The scenenario is the following:

We have multiple subnets in our network. One of them is the security one which is 10.224.2.xxx

Computer A is connected directly into it. Ethernet cable comes out of the wall and goes into her Intel NIC.

Computer B is also connected directly into it. However, ethernet cable comes out of the wall, goes into a dock and then through the USB cable, gets internet.

Computer C is connected to our wireless security network which is 10.224.4.xxx
This computer is allowed on the firewall to talk to 10.224.2.xxx

All three computer have Webroot SecureAnywhere installed. The printer is an EPSON Workforce WF-4640. IP is 10.224.2.122 / 255.255.254.0 / 10.224.2.1 gateway / no iPV6 / 192.168.50.18 & .19 are DNS's. Printer has static IP.

I proceeded to install the drivers on all three computers. Here is where the problem comes.

Computer A installs just fine. Finds the printer on the subnet and completes installation. I can print and scan FROM the computer. I can also scan FROM the printer. When I go to "Document Capture Pro", I can see scan to: COMPUTER A on the list.

Computer B also installs just fine. Finds the printer and completes the installation. I can print and scan FROM the computer, but I cannot scan FROM the printer. It just wont list COMPUTER B at all!. I tried plugging the ethernet cable directly into the laptop, but still, the printer will not show computer B in the scan to list.

Computer C the same story, but worse. I cannot finish the installation properly because it will not find the printer. It is obviously on a different subnet, but it will not let me type in the address so I just cancel the printer finder part. I manually go to control panel and adjust the IP parameters. Same thing, I can print and scan from the computer but cannot scan FROM the printer. It will not list Computer C in the list.

I have tripled checked the EPSON Scan software on each PC. Each has the IP parameters set properly. I have spent days installing and reinstalling drivers, but no luck. Printer has updated firmware. I tried disabling Windows firewall, nothing.
At first I wanted to think it was Webroot, since there is a review on Amazon from a guy that had the same problem, but using Norton. However, how come Computer A works just fine?
When I though it was the dock, I quickly found out it was not as explained in Computer B when I plugged it directly.

At this point, Im running out of ideas. Im not even sure where else to go.

 

Brother printer DCP 1610w not scanning to my computer

Hi Linden,

Outdated scanner driver is one of the possible reasons why you are unable to scan using your Brother DCP 1610W printer. For us to assist you better, kindly answer the following questions:

• Have you made any changes to your computer prior to this issue?
• What troubleshooting steps have you done so far?
• Which version and OS build number of Windows 10 is currently installed? To check, press the
  Windows key, type winver, and press the
  Enter key.
• Have you tried to download and install the latest driver for your printer from the manufacturer's website?
• Do you receive any error messages?
• What program are you using to scan files?

Regards.

 

My Brother printer no longer will scan wirelessly since upgrading to Windows 11

Hi Carlo T.,

Thank you very much for taking the time to reply to my post. I tried doing that before I posted my initial question... That being said, I tried it again and unfortunately, it did not work. I even tried the Windows 11 patch that Brother listed on the drivers page and that did not help either.

I am able to print to the printer via wireless, but I can no longer scan.

If you or anyone else has any other suggestions, please send them my way.

Thanks again.

David N.