Windows 10: i have ryzen 7 5800x and tpm 2.0 but i can't install windows 11

AMD Ryzen 7 5800X 8-Core Processor 3.80 GHzRAM 16 GBSSD for System 500 GB ~75% freeWindows 10 Pro 22H2B450 Aorus MTPM 2.0 Active in BIOS F60 UEFI all on ONLYtpm.msc shows that it is active...but when I check the performance to install Windows 11, it always tells me that Security is not turned on. Already starting to give up on upgrading to Windows 11. Anyone have any ideas?

:)

 

TPM not usable, cannot install Windows 11

My machine is not able to be upgraded to Windows 11. Here is what my system info says:

• Device Encryption Support Reasons for failed automatic device encryption: TPM is not usable, PCR7 binding is not supported, Hardware Security Test Interface failed and the device is not Modern Standby, Un-allowed DMA-capable bus/device(s) detected, Disabled by policy, TPM is not usable
  
• Motherboard Gigabyte B450M S2H
  
• Processor AMD Ryzen 5 3600 6-core
  

I tried following the instructions at Enable TPM 2.0 on your PC - Microsoft Support

I got into the BIOS and it says that it is enabled, but no device found.

 

Ryzen 7 5800X shuts off soon after boot

I recently upgraded my ryzen 7 1700x to a ryzen 7 5800x. I updated my BIOS on my MSI B350m Gaming Pro. MSI's bios website says that the motherboard is compatible with the CPU. Upon booting, It runs very slowly due to a slow ram setting (or so I think). My RAM is supposed to run at 3200mhz but it says it defaulted to 2133mhz. The computer boots in windows 10 for a few moments, but suddenly the fans rev up to max and it shuts off before I can even install drivers. My cooler is a coolermaster ML120 AIO (Single Fan). I did some research and knew that it couldn't cool the 5800x, but I thought I could at least surf the web until I order a better cooler. How can I fix this?

 

Ryzen 5800x + X570 tomahawk WIFI BSOD

Hello there,

I recently purchased a MSI x570 tomahawk wifi and after assembling i am facing lots of BSOD issue. After days of reading troubleshooting steps on linustechtip, MSI, AMD, reddit forums i am still facing BSOD UNLESS i turn off Core Performance Boost (CPB) in BIOS. Hope i can get some further help here. Please find below a summary of my setup below:



My new setup:



CPU: AMD Ryzen 7 5800X (NEW)

MOBO: MAG X570 TOMAHAWK WIFI (NEW)

DRAM: Corsair Vengeance LPX DDR4 16GB X 2, 3600Mhz (CM4X16GD3600C18K2D-CN ver 3.44, CM64X16GD3600C18K2D-CN ver 5.49) (NEW)

GPU: ZOTAC GEFORCE RTX 2070 Super Twin Fan 8GB (OLD)

PSU: Cooler Master MWE Gold 750 Full Modular 80+ Gold (OLD)

SSD: Samsung EVO 980 PRO M.2 (NEW)

BIOS version: E7C84AMS.150

CPU cooler: AMD Wraith (NEW) *Planning to upgrade to a AIO soon after i get this bsod sorted out.





Issues faced:

1. Constant BSOD (WHEA) before reaching Windows.
   
2. Sometimes able to go into Windows but after 1-2min of idling (low load) will BSOD (WHEA)
   
3. Windows event viewer showing Kernel power (41)
   

Troubleshooting steps taken:

1. Reinstalling windows from flash drive.
   
2. Updating bios, chipset, NVIDIA and windows /drivers update to latest.
   
3. Reseat CPU, PSU, RAM, GPU (basically all connections).
   
4. Following AMD troubleshooting steps.
   
5. i) Clearing CMOS by removing MOBO battery.
   
6. ii) Set power supply idle to Typical in BIOS.
   
7. iii) Select balanced power plan in Control Panel.
   
8. iv) Sliding performance and energy slider to middle.
   

1. Swapping DIMM slots between 2,4 and 1,3 and trying with 1 ram only.
   
2. Turn off C-state BIOS.
   
3. Turning off XMP.
   
4. Turning off PBO. (Precision Boost Overdrive)
   
5. Manually setting Vram to 1.35V.
   
6. Running memtest86 using OLD MOBO and OLD INTEL CPU with NEW RAM. 4passes with 0 errors.
   
7. Chip temperature should not cause BSOD as im constantly checking and only reaching 35-45deg on idling. Setup in aircon room with ambient 23-24deg.
   
8. Running memtest86 on NEW MOBO with NEW RAM.
   
9. Testing with a different RAM, MOBO, and PSU model (borrow from friend)
   

Further troubleshooting using friend's mobo and chip:

1. Able to run under load and idle after installing my 5800x onto my friend's X570 gigabyte gaming x with CPB turned on and XMP.

2. My friend's 3700x is able to run in my x570 tomahawk wifi board with CPB turned on and XMP.

3. I have RMA the X570 tomahawk wifi mobo and still facing the same issues with the new 5800x CPU.



I'm confused as to why the 5800x is able to run stable on the gigabyte board but not on the MSI board, and the 3700x cpu is able to run stable on the both boards. The ONLY way to get the pc (5800x + MSI x570) to run windows without BSOD is to TURN OFF CPB. (Tested for more then 5hours with iding load no BSOD). As soon as i turn on CPB, BSOD (WHEA) appears at the login screen.

Hope to get some advice and thank you in advance.