Windows 10: Is the current windows update bugged?

I keep getting a notification about windows 11 update version 24H2 But I'm unable to install it. It keeps giving me an error saying my NVMe disk isnt "ready for this version of windows." I am on windows 11 and my NVMe disk is a WD blue sn580 2tb. It has the latest drivers and everything.. I tried just ignoring the update but it continues to notify me about it. Is this a bug with the windows update or is it on western digitals side? If its neither do I have to replace the NVMe?

:)

 

Taskbar bug: switching to another window -will not appear at the front


Follow either of these steps to fix the issue with the Active window hiding behind.

Method 1:
I suggest you to disable window by hovering over it with the mouse and check if it helps. To do so I suggest you to try the below given steps and check if it helps:

1. Press Windows key + X key and click on Control Panel.
2. Select or click Ease of Access.
3. Click or tap onEase of Access Centre.
4. Click on Make the Mouse Easier to Use was uncheck Activate Window by hovering over it with the mouse.
5. Check if issue is resolved.

Method 2:
I would suggest you to completely uninstall the touchpad driver and reinstall it. Kindly follow the below given steps.

1. Press “Windows key + X” and click on “Device Manager”.
2. In the list of devices, you should see the touchpad drivers.
3. Right click on the device and then select "Uninstall".
4. In the uninstall dialog, make sure you select the option to delete the driver package from the system. This causes the driver package installed earlier to be deleted.
5. In the Action menu of Device manager, select “Scan for Hardware changes” option. This will cause the device driver to be reinstalled. Once the driver is installed, close all windows and restart the computer.

 

Windows Updated(16299.309).KB4088776 Restart is required to complete.

Hi dalchina. Good news, I followed your suggestion and reinstalled the update and now it appears as "installed correctly" *Biggrin Maybe it was not necessary to run the Windows Update Troubleshooter or maybe if necessary. But using it I do not think it could have worsened something. The installation was very fast, unlike the first time it showed step 1 and step 2 completed.

Thanks for the suggestions and for the time to respond Best regards.


And thanks for the tip of that program, I'll have it on my list.

 

Intel Readies P55 Chipset B3 Stepping Update

Intel's is readying a hardware update for its P55 Express chipset, currently the only core-logic for the company's brand new socket LGA-1156 processor platform. The new B3 stepping of the P55 PCH will bring with it a little more than new MM number and S-spec numbers. A list of changes is as follows:

• New MM number and S-spec numbers for the converted products;
• Firmware and minor BIOS updates are required with the conversion;
• Processor MRC/microcode update required to enable future processors;
• Recommended storage driver upgrade from Intel MSM 8.9 to Intel RST 9.5.

Although it is listed that the MRC update enables 'future processors', Intel, in a statement issued to X-bit labs assured that the current B2 stepping of the chipset (found on current socket LGA-1156 motherboards) does not leave out support for any of Intel's new LGA-1156 processors that are slated for release in the very near future. The dual-core "Clarkale" 32 nm processor will be supported by both B2 and B3 steppings of the chipset.

P55 B3 stepping is pin-identical to P55 B2, and hence motherboard vendors will not have to come up with new designs. Sampling of the new stepping began as early as on October 02, 2009, and it is scheduled for shipment to manufacturers by the 7th of December, 2009. P55 is the performance core-logic for the LGA-1156 platform. It supports Core i5 and Core i7 "Lynnfield" processors with discrete graphics.

Source: X-bit labs