Windows 10: Is there a way to enable WinRE if my pc is on BSOD?

Hi, earlier today, I attempted to go back to windows 10. My pc went into BSOD. Recovering to previous windows, goes to blue screen and pivots back to this statement again. My WinRE is disable so there’s no way to go into safe mode to update or fix this issue. Is there anything else I can do?

:)

 

PC reboots (no BSOD) on CPU stress

Hi fellow TPU members,

not too long ago, the box my gf's PC was transported in gave way on the stairs. Yes, you got it right, that sent a PC tumbling down a flight of steps alright.

Stuff broke. Also, stuff remained intact somehow.

I bought her a new case, new CPU cooler and we removed the floppy drive, so far so good. But the PC started crashing for no apparent reason, without a BSOD.

I tested:

• Memtest86+, left overnight, 0 errors
• Scanned the HDD for errors, nothing there
• Left FurMark burning up the GFX card and drawing some power, no problems there
• Ran Ubuntu from a Live CD doing nothing special, didn't crash
• Ran OCCT, Linpack, Prime95, all 3 caused reboots within minutes
• Oh, and I disabled "Restart on error" so I'm sure it's not a BSOD.

Now, I can still try and test something CPU intensive on Ubuntu, but my guess is the CPU didn't survive.
Before I do anything drastic like whippin' out the magic wallet and get her a new AMD quad, is there anything I didn't see?
I'm guessing the motherboard could be borkered as well, but can I check that other than replacing the CPU with a working one?
Any suggestions on which proggies I can use from an Ubuntu Live CD to stress the CPU?

 

BitLocker won't enable on Windows 10 after update on Aug 9

Hi Brenda,

I would be happy to assist you.

Before I assist you I would like to know the information below,

• 
  Do you have a Windows 10 copy of the operating system?
  

I suggest you check whether the Bit locker is ON or OFF using the steps below.

Can you verify if BitLocker is enabled or disabled on your device? You can Enable/disable BitLocker by going to Desktop and follow these steps:

• 
  Swipe Right to Left to bring up the Charm.
  
• 
  Choose Settings.
  
• 
  Choose Control Panel.
  
• 
  Select BitLocker Drive Encryption.
  
• 
  Verify whether BitLocker is on or off on each device.
  

Also I suggest you to enable the WinRE so that you can enter the bit locker key and proceed.

When WinRE is disabled, you cannot enable BitLocker, and you receive an error message that resembles the following.

This PC doesn't support entering a BitLocker recovery password during startup. Ask your administrator to configure Windows Recovery Environment so that you can use BitLocker.

The solution would be to manually enable the windows recovery environment:

• 
  Copying the winre.wim file from c:\windows\system32\recovery\ to a folder on a recovery partition. (The partition need to have a drive letter at this point.)
  
• 
  Set the RE Image path. Example: reagentc /setreimage /path r:\recovery\windowsre
  
• 
  Enable RE with command: reagentc /enable
  
• 
  (You may remove the drive letter for the recovery partition after you have done this.)
  
• 
  Bit locker will be enabled.
  

If the issue still persists, suggest you to post your query on the below link.

https://technet.microsoft.com/en-us/library/hh831507(v=ws.11).aspx

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

Thank you.

 

Unable to boot the PC stuck in WinRE mode

Hi,

Thank you for writing to Microsoft Community Forums.

I understand how difficult it can be when the PC doesn’t work the way it is supposed to. I appreciate your effort in trying to resolve the issue by performing troubleshooting steps. For better understanding of the issue, please
respond to the questions below:

1. Are you aware of any changes being made to the PC?
   
2. Do you receive any error code when you try to boot the PC normally?
   
3. What are the troubleshooting steps you have tried?
   
4. What is the error you receive while performing reset?
   
5. What was the result of automatic repair?
   

Meanwhile, you can try removing any external devices connected to the PC and check if you are able to boot the PC.

However, I would suggest you to follow the steps mentioned below and check if that helps.

Method 1:

I would suggest you to try booting the PC to safe mode and check if that helps.
Refer the article
Start your PC in safe mode in Windows 10. If the PC is working fine in safe mode, perform a clean boot being in safe mode environment check.

Performing a clean boot will start the computer with minimal set of drivers and programs, to determine whether a background program is causing the issue. Some of the Startup programs will not load after performing a clean boot
on the computer. However, that functionality will return when you reset the computer to start normally after finishing the troubleshooting.

To perform a clean boot on the computer refer to the article

How to perform a clean boot in Windows.

Note:
Please refer the section Reset the computer to start normally after clean boot troubleshooting
to boot the computer in to normal mode after troubleshooting.

Method 2:

Try troubleshooting startup issues. You can refer the article on

troubleshooting common startup issues and see if that helps.

Note: While performing chkdsk on the hard drive, if any bad sectors are found on the hard drive then chkdsk tries to repair that sector if any data available on that might be
lost.

If you have an external hard drive, you can take the backup of the data by following the steps mentioned below.

1. Open command prompt window by following the article
   
   troubleshooting common startup issues.
   
2. On the command prompt window type,
   notepad.exe and hit enter.
   
3. Now click on File
   and click Open…
   
4. On the Open file window, click on
   This PC
   
5. Now navigate to the location
   C:\Users\UserName\ select the folder that you want to backup to the external drive.
   
   Note:
   To see all the files on the Open dialog box, change the
   files of type to All files.
   
6. Right click on the file/folder
   and select Send to and select the external hard drive.
   

If the issue persist, please get back to us with the result of troubleshooting steps to assist you further with the issue.

Regards,

Prakhar Khare

Microsoft Community – Moderator