Windows 10: Laptop keeps booting BIOS after windows 11 update

Hello, I would like some help to my problem please. I accept updating windows 11 and now I turn on my laptop again and it keeps entering BIOS. I've tried turn off and on several time and it keeps doing the same.... What should I do please? Thanks

:)

 

Secure boot isn't turning on in HP laptop (windows 11)

Hello Mohd_357,

Welcome to Microsoft Community.



I understand the frustration you’re facing with Secure Boot on your HP laptop. Let’s troubleshoot this issue step by step:

1. Load HP Factory Default Keys:
   
   • Go into the BIOS settings.
     
   • Navigate to System Configuration > Boot Options.
     
   • Look for an option to Load HP Factory Default Keys. If available, select it.
     
   • Check if Secure Boot becomes available after doing this.
     
2. Disable Fast Startup:
   
   • Boot into your operating system (Windows 11).
     
   • Open Settings.
     
   • Go to Updates & Security > Recovery.
     
   • Click Restart Now under “Advanced startup.”
     
   • Wait for your PC to boot into the system recovery menu.
     
   • Select Troubleshoot and then choose Advanced options.
     
   • Finally, select UEFI Firmware Settings.
     
3. Check BIOS Mode:
   
   • Ensure that your Windows 11 installation is in UEFI mode, not legacy mode.
     
   • If your notebook’s BIOS mode is set to legacy, you won’t be able to enable Secure Boot. You may need to reinstall Windows 11 from an EFI boot source.
     
4. Reset BIOS settings to Default:
   
   • Reset BIOS settings may restore secure boot settings to normal factory state.
     

Regarding TPM 2.0:

• Your PC may not have TPM (Trusted Platform Module) support, which is required for Windows 11.
  
• Additionally, Windows 11 requires an Intel 8th gen core processor or newer.
  

I hope it can solve your problem.

Thank you for your patience and cooperation.



Best Regards,

 

Alienware Area 51 m15x BIOS Update Released

If you were among the group of people experiencing overheating issues with your Alienware Area 51 m15x laptop, then there are some good news for you. A new BIOS update, version X29b P3A30 is now available. The update allegedly allows VGA fans to increase up to 5400 rpm and thus better cool the GPU. To obtain the new BIOS, you'll need to email the m15x support line (L: Area51_m15x@alienware.com). In reply you should receive a link to the BIOS .zip archive. Once you download the small file, Alienware recommends to follow the steps described in the Read full story marker.



Open Nero Ultra Edition, click Backup, and then click “Burn Image to Disc.” Next, select the file “m15x_x29b.iso from the unzipped folder.

• Plug your AC adapter in
• Disconnect all third-party peripherals
• Don’t turn off the computer or restart it during the update
• Don’t eject your DVD/Blu-ray drive during the update.

Steps:

• Open BIOS by tapping F12 during boot
• Set BIOS to boot from your CD-ROM drive first
• Save and exit
• Upon reboot, the BIOS flash update will proceed
• Click “Yes” through the prompts
• Restart

Source: LAPTOP Magazine

 

Laptop not booting after bios update

Take it apart and try his suggestion is what I would do next. Still what a pain disassemble laptop to fix bios.
RE: Latitude 3330 BIOS update failure
Hi Alex,
sorry about my late. I don't know that you could fix your problem now, but I try help you.
You need remove the Lan card (modular part on motherboard ), because you have a problem with UEFI boot. You can enter in BIOS, if the LAN part is unplugged



RE: Latitude 3330 BIOS update failure







Hy everyone,
I fix this Bios Post error problem.

1. Switch off the computer.
2. Disconnect the AC adapter from the system.
3. Remove the battery from the computer
4. Remote HDD, keyboard, Palmrest
5. Put out the CMOS battery
6. Raise up the LAN/VGA part (2 screws)
7. Take a USB keyboard, connect the AC adapter and press F2
8. If you see the BIOS, almost finished.
9. Put on The CMOS battery, and step in: System configuration / integrated NIC / Turn off "Enable UEFI Network Stack"
10. Turn off and raise down the LAN/VGA part. Test Again. If everything is working you done.

I hope, I could help you
Regards
David