Windows 10: ms-settings with Group Policy Management not allowing full access for Administrators

Need to setup access to all settngs in control panel ms-settings for administrators but block certain ms-settings for users using Group Policy management. Any suggestions?

:)

 

Group Policy on home machine?!?!?!?!?


Hi,

Had the same issue on a number of occasions. This is what solved it for me:


Steps to fix 'Some settings are managed by your organization' message in Windows 10
Make sure you have administrator rights and follow the steps below:

Step 1: Launch Run prompt by right clicking the Windows Start menu icon. Type in gpedit.msc and click OK or Enter.
Step 2: In Group Policy Editor (gpedit.msc), go to Computer Configuration/Administrative Templates/Windows Components/Data Collection and Preview Builds.
Step 3: Find the Allow Telemetry item and double-click it to edit the policies.
Step 4: Change the setting to Enabled. Change the drop-down menu entry to 3-Full and click Apply.
Step 5: Now open the item again and change its Setting to Not configured and hit the Save button.
The message should no longer stop you from accessing various system settings in Windows 10.

Cheers, *Wink

 

Windows 10 error: "Windows couldn't connect to the Group Policy Client service. Please consult your system administrator"

Hi Rico,

Thank you for posting in Microsoft Community, we appreciate your interest in Windows 10.

I understand the inconvenience you are facing with accessing the operating system.

Do let us know the following to assist you better:

• Which edition of Windows Operating System are you using?
• What all the troubleshooting steps have you performed?
• Have you installed all the pending updates on your Operating System?
• Have you installed any third-party anti-virus software on your system?

I suggest you to try few of the below troubleshooting steps and check if it helps.

I suggest you to Stop the Group Policy service, restart and set it to Automatic.

Group Policy Client service, this service is responsible for applying settings configured by administrators for the computers and users through the Group Policy component. If the service
is disabled the settings will be applied and applications and components will not be manageable through Group Policy.

Step 1: Stop the Group Policy Client service.

• Press Windows Key + R on the keyboard and type
  services.msc, Services window gets opened.
• Search for Group Policy Client service, right click on it and click on
  Stop.
• Restart the computer.

Step 2: Start the service and set it to automatic:

• Press Windows Key + R on the keyboard and type
  services.msc, Services window gets opened.
• Search for Group Policy Client service, right click on it and click on
  Properties.
• Start the service, set
  Startup type to Automatic.

Hope it helps. Reply to the post with an updated status of this issue for further assistance.

 

Unable to access task manager after changing group policy for recovery settings

Hello Andrew,



Thank you for writing to Microsoft Community Forums.

1. Is the PC connected to a domain network or a personal network?
   

The issue might be because the task manager policies have been affected due to the changes.



I suggest you to follow the steps mentioned below to fix the issue.



Note:
Important this section, method, or task contains steps that tell you how to modify the group policy. However, serious problems might occur if you modify the group policy incorrectly. Therefore, make sure that you follow these steps carefully. For added
protection, create a system restore point. Then, you can restore the system if a problem occurs.



Refer the article to
create a system restore point.

1. Go to "Start" -> "Run" -> Write "Gpedit.msc" and press on "Enter" button.
   
2. Navigate to "User Configuration" -> "Administrative Templates" -> "System" -> "Ctrl+Alt+Del Options".
   
3. In the right side of the screen verity that "Remove Task Manager"" option set to "Disable" or "Not Configured".
   
4. Close "Gpedit.msc" MMC.
   
5. Go to "Start" -> "Run" -> Write "gpupdate /force" and press on "Enter" button.
   
6. Restart the PC.
   

However, if you still face the issue I suggest you to post your issue on

TechNet forum.



Hope it helps.

Let us know if you got the help you needed by clicking ‘Yes’ or ‘No’.



Regards,

Prakhar Khare

Microsoft Community – Moderator