Windows 10: Multiple BSOD and stop codes most commonly HYPERVISOR_ERROR

I recently built a new PC and after a couple of weeks of smooth operation, decided to add more RAM for my virtual machine workspace I had set up with HyperV. I initially had 32GB of RAM installed so I added another 32GB to this, intending to dedicate half to the VM. I didn't notice until later that the clock speeds were different as the RAM had a very similar product code, and after running into the issues after installation, I took them out. However, during this hardware modification, I had to remove and reinstall my CPU fan due to its size, which could have potentially caused some issues.So

:)

 

BSOD with multiple stop codes

• Problem
  

The problem is that I get a blue screen of death (BSOD) frequently for a few months now, and it increases in frequency once I've had the first one. For example, if I leave my computer on for a while, it'll run normally for a few hours before I get my first BSOD. After I get a BSOD, I get a lot more afterward over the period of 30 mins - 1 hour. The stop codes I get are different every time so there's no way of saying which one I get the most.

• Problem history
  

I don't remember exactly when I had this problem or what triggered it. But at the time I hadn't changed any hardware components or installed new software. However, I used to only get the stop code IRQL_NOT_LESS_OR_EQUAL. After some attempts of troubleshooting, I started getting all the stop codes besides IRQL_NOT_LESS_OR_EQUAL to this moment. I don't remember which step exactly of troubleshooting triggered this change though.

• Specs:
  

1. Windows: Windows 10 x64
   
2. Motherboard: Asus Strix B450-F Gaming
   
3. CPU: AMD Ryzen 5 3600
   
4. Memory: Corsair CMK32GX4M2E3200C16 Vengeance LPX 32 GB
   
5. Hard disks: KINGSTON SA400S37240G / WDC WD10EZEX-21WN4A0
   
6. Graphics card: MSI GeForce RTX 3060 GAMING X
   
7. Power supply: don't remember exact model but it's Corsair 550W
   

• Troubleshooting:
  

1. Changed GPU (from GTX 1060 to current)
   
2. Changed RAM
   
3. Turned D.O.C.P off
   
4. Turned D.O.C.P on
   
5. Updated all drivers (chipset, graphics, etc..)
   
6. Updated BIOS
   
7. memtestx86 (no errors)
   
8. CheckHealth
   
9. Updated windows
   
10. Installed fresh windows (wiped everything) and reinstalled all drivers.
    
11. Tried different RAM that I am sure is not faulty
    

• Notes:
  

1. I tried installing fresh windows multiple times and I noticed that every time I get insanely many BSODs before I install the chipset driver. Then it returns to normal frequency as stated in the 'problem' section.
   
2. Every time I check the performance monitor I see the message below or something similar:
   
   
   
   

 

SYSTEM_SERVICE_EXCEPTION and HYPERVISOR_ERROR BSOD's

Hello,

In the past few weeks, I've been regularly experiencing BSOD's, typically SYSTEM_SERVICE_EXCEPTION and HYPERVISOR_ERROR with BlueScreenView blaming ntoskrnl.exe

I've already tried the following (in order):

• Complete re-install of Windows 10, followed by the bare minimum of software
• Complete driver re-installation with Driver Easy
• Removal of 1 RAM DIMM, which seemed to work out but despite that, I had another BSOD today.
• sfc /scannow, did not find any integrity violations
• chkdsk doesn't return any issues

Also:

• Memory diagnostics did not return any issue
• SMART values of the disks are all right. Only the disk with the D: partition on it is showing some ageing, but it only has Steam games on it and the BSOD's happen outside gaming so that shouldn't be relevant.

What's next to try? Any info to add?

Memory dumps to be found here: Microsoft OneDrive

 

BSOD when coming out of sleep, multiple error codes

Thanks for the assistance, I've run all the necessary steps. It looks like there might be an issue found when running that first command. I have also installed all the driver updates recommended by the dell support check.

You can find the logs of the command prompt window in the cmd.log file

cmd logs.txt