Windows 10: My computer boots into windows just not BIOS

I need some help!



Specs:

Gigabyte X570 Elite

Ryzen 7 3800x

32GB RAM

5 drives 3 ssds, 2 HDD

1080ti

850W PSU

I was messing around in my bios and I turned on fast boot to ultra before it was disabled. After I saved and exited in my bios my computer sat at a black screen. I took every drive out except my m.2 Boot drive and with no luck. I couldn't even get into the bios. I cleared the CMOS twice and plugged every drive-in and now my computer does boot to windows. I tried safe mode to just see if that changes. nothing. When I try booting to BIOS the logo appears with the keys to hit and I do that it flashes only for a second, "BIOS has been reset. Please re-config your BIOS setup items if needed." then to a black screen. I need to get into bios to one enable XMP, two make sure everything is running fine, and three to tweak some settings I had before when it ran normally. Without hitting Del it boots to windows just fine, My bios version is mostly up to date. Version F30 9/15/2020



Any help is appreciated!

:)

 

Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure the disk's controller is enabled in the computer's bios menu.

Hi Matthew,

There are several possible reasons as to why your computer is not detecting an SSD drive. This could be caused by incorrect BIOS settings or device drivers that need to be updated. Since you already tried the suggestion of Andre Da Costa and this allowed
your computer to detect the SSD already, we would like to further clarify your concern by asking the questions below:

• If you were already able to install Windows on the SSD, have you already attempted to change the boot order in the BIOS menu?
• Which version of Windows did you install on the SSD?
• What other troubleshooting steps have you attempted?

We look forward to your response to our queries.

 

bios

Hi all i am new in this forum, i need meanings step by step of each item listed in the bios Phoenix-Award

 

Windows 10 will only boot if selected from the BIOS boot menu.

Hello,

Thank you for contacting Microsoft Community.

We understand the inconvenience you have experienced.

• You mean to say, every time you need to make changes to Boot Order in BIOS, to start your computer correctly?
• What is the make and model of your computer?

I suspect that the problem might be due to outdated BIOS update
or with Boot Configuration data. Suggest you to check for the latest BIOS update and Chipset drivers for your device hardware on Manufacturer website. If you find a new one, try to update the same to see if it correct
the issue. If problem still persist, then I suggest to rebuild Boot Configuration Data to see if it makes any difference.

Let us try to repair your computer by creating a Windows 10 Bootable media (I.e. USB or DVD) using
Media Creation Tool.
Use your computer or some other connected to Internet for creating a Bootable media (Windows 10 ISO image file). Once you're ready with Bootable Media, follow the below mentioned
steps.

• Insert the Windows installation disc in the disc drive or connect USB media, and then start the computer.
• Press a key when the message Press any key to boot from CD or DVD appears.
  
  If your PC does not detect the media automatically
  • During the restart process, read the screen for any instructions that explain how to interrupt normal startup and enter the basic input/output system (BIOS) setup utility. Most PCs use the F2, F10, ESC, or DEL key to begin the BIOS Setup.
  • Look for a tab in the BIOS Setup Utility that is labeled Boot Order,
    Boot Options, or Boot. Following the directions on the screen, use the arrow keys to go to the
    Boot Order, then press Enter.
  • Locate the CD, DVD, or USB flash drive (this might be called Removable Device) in the Boot list. Following the directions on the screen, use the arrow keys to move the drive up so that it appears first in the Boot list. Press Enter. The boot order
    sequence is now changed to boot from the CD, DVD, or USB flash drive.
  • Press F10 to save your changes and to exit the BIOS Setup Utility. Select Yes in the confirmation window. The PC will restart. Allow the PC to restart normally. The scan will take a few minutes and remove any malware that may be infecting your computer.
• Select a language, a time, a currency, a keyboard or another input method, and then click Next.
• Click Repair your computer.
• Click the operating system that you want to repair, and then click
  Next.
• On the Choose an option screen, select Troubleshoot. Select
  Advanced Options > Command Prompt
  under Advanced Options.
• Type Bootrec /RebuildBcd, and then press
  ENTER. This command will rebuild boot configuration data if in case any issue with Boot files causing this issue.

Once you done with the above steps, see if the problem still persist.

Let us know how it went.