Windows 10: My pc fails to auto repair, restore the pc and so after a couple changes in the Bios.

I swapped my fabric ram to a 32gb corsair vengence ddr5 into an acer PO5-640, worked fone but the tutorial video said to activate x.m.p in the Bios and also to change something in the boot list so instead of “windows boot” default into “removable devices”. After i made that mistake with the removable devices the pc gave me a blue screen with something i berely could read and i think it was about drivers or something related to windows, then it booted and now its stuck on “preparing automatic repair” then “diagnosimg pc” then puts me in a blue screen with “automatic repair failed, try restar

:)

 

Auto repair loop triggered by failed system restore

I was having connection issues with my PC and attempted to use a restore point to fix the issue, however it would seem the restore point failed and completely destroyed my computer. Upon finishing it's attempt at restoring the system the Computer shut down unexpectedly - I say 'unexpectedly' because it gave me the message below:

Your PC has ran into a problem

When the computer restarted it was locked in a loop in which "Auto-repair" repeatedly failed to fix the system. I attempted to undo the restore but the Undo failed. Does anyone know how I should move forward?

I should probably clarify further by noting that, as far as I can tell, I'm stuck in a Auto repair loop as a result of a failed system restore.

I'm unable to undo the restore as attempting to do so results in a 0X80070003

 

Pc bsod to bios

Currently replying on iPhone, I’ll give you a proper timeline Step 1) during the program of tuneup plus my pc bsod 3 times but I was finally able to get the info Step 2) Restore point was easy and done quick which now leads to step 3 Step 3) After starting the WDV my pc bsod with the stop code of “System thread exception not handled” following the steps I open command prompt and tried to turn it off which says that nothing was changed, so then after a couple of bsod’s later I manage to go back to my restore point which now leads to a problem I cant seem to fix where when I try to open my pc it says something is wrong with my pin with error code (0x80090016) If needed I do have the tuneup plus info Trying to solve the pin problem if anyone suggestions please inform me.

 

My pc will only turn onto the bios settings

If your PC is only turning on to the BIOS settings and you are unable to boot into Windows, it may be due to a hardware issue or a problem with the operating system. Here are some steps you can take to try and fix the issue:

1. Check the boot order in BIOS:
   

• Enter the BIOS settings by pressing the appropriate key (usually F2 or Del) during startup.
  
• Look for the "Boot" or "Boot Order" section and ensure that the hard drive or SSD that contains the operating system is set as the first boot device.
  
• Save any changes and exit the BIOS.
  

1. Check for loose connections:
   

• Turn off your PC and unplug it from the power source.
  
• Open up the PC case and check all connections between components (such as the hard drive or SSD and the motherboard) to ensure they are properly seated.
  
• Close the PC case, plug it back in, and turn it on to see if the issue is resolved.
  

1. Perform a startup repair:
   

• Use the Windows installation media (such as a USB drive or DVD) to boot into the advanced options screen.
  
• Select "Startup Repair" and follow the prompts to attempt to repair any issues with the Windows operating system.
  

1. Reinstall Windows:
   

• Use the Windows installation media to perform a fresh install of the operating system.
  
• Note that this will erase all data on the hard drive or SSD, so make sure to backup any important files beforehand.
  

If none of these steps solve the issue and you continue to see the "no bootable device detected" message, it may be due to a hardware failure such as a faulty hard drive or SSD. In that case, you may need to replace the failing component or seek professional assistance.