Windows 10: My PC keeps blue screening with different error codes, so i did a SFC /scannow and have the...

heres the link to the CBS, if someone could take a look and guide me to fix the problems i would appreciate it.

thanks

https://drive.google.com/drive/folders/15oA4yUdpBV9w7D_IayfuMhf7WmXxX0C4?usp=sharing

:)

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.

 

SFC /SCANNOW Errors After Update

I've just updated a Windows 8.1 Pro PC to Windows 10 using the Techbench ISO which updated without any problems. However, I've just run sfc /scannow and it found errors it could not repair. I have managed to get sfc /scannow to run without errors - see what I did below:

1. Ran sfc /scannow which showed error "Windows Resource Protection found corrupt files but was unable to fix some of them."
2. Ran Dism /Online /Cleanup-Image /ScanHealth which reported "The component store is repairable."
3. Ran Dism /Online /Cleanup-Image /RestoreHealth which failed with Error: 0x800f081f "The source files could not be found.Use the "Source" option to specify the location of the files that are required to restore the feature."
4. Mounted the W10 Techbench ISO and ran Dism /Online /Cleanup-Image /RestoreHealth /source:wim:G:\sources\install.wim:1 /limitaccess which reported successfully "The restore operation completed successfully."
5. Ran sfc /scannow wich completed successfully with report "Windows Resource Protection found corrupt files and successfully repaired them."

Please advise:

1. Why would sfc /scannow fail on a newly updated installation which ran sfc /scannow error free immediately before the upgrade?
2. Why did I have to use install.wim from the Techbench ISO at step 4 above for Dism /Online /Cleanup-Image /RestoreHealth to work and will I have to use install.wim from the Techbench ISO every time I need to run this Dism command?
3. How can I configure my PC so it has the correct install.wim file for the Dism command to work properly?

 

sfc /scannow error

Thanks.
After above steps, I rebooted my laptop and did sfc /scannow. It is OK now.