Windows 10: My PC keeps crashing, i have brought my pc to best buy 3 times and i dont know what to do...

so, the first time it happened i had put a new graphics card in without the proper steps, just put a new one in the old was a 3060 and the new one was an rx 6700 xtand after i put the new one in i started seeing flickering and issues on roblox and other things, so i thought why not put the old one in, and ever since then its been blue screening after being on for 7 hours+ and like i said i have brought it to best buy 3 times. i dont know what it is, i have tried a new cord for the psu, clean installing windows, resetting the pc multiple times, updating the bios which might be an issue too if

:)

 

Forza Horizon 3 Crash on Gameplay

Hi,

Thank you for writing to Microsoft Community Forums.

I understand that Forza Horizon 3 keeps crashing.

• Are you aware of any changes made to the computer recently?
  

I suggest you refer and follow the steps mentioned in the article and check if that resolves the issue. Refer to the article
My Game is Not Launching or is Crashing on PC.

Let us know how it goes.

Regards,

Zaki

 

Latest windows 10 Update keeps crashing my PC

The latest windows 10 Update that brought Cortana to my PC keeps crashing it

Originally it kept crashing before the log in screen

Now I can log into my PC but try to do anything on it and something crashes. It's not the same process that keeps crashing every time to. Sometimes it's a critical process other times it's not. Sometimes it still crashes on startup and it goes into an endless
cycle of boot crash reboot crash and re-peat.

 

PC Keeps crashing

Hi Vijay,

Thank you for writing to Microsoft Community Forums.

I understand that your PC keeps crashing.

1. Do you get any error message or code when the computer restarts after the crash?
   
2. What’s the make and model of the computer?
   

I suggest you to follow the steps mentioned below and see if that helps.

Method 1: Disable Automatic Restart on System Failure

Press WIN + R to launch the Run utility.

Type in sysdm.cpl and then hit Enter to launch System Properties.


Click on the Advanced Tab
and under the section labeled as Startup and Recovery.

Click on the button that says Settings.

A new pop-up window will now open. Under the section called System failure, uncheck the option labeled as Automatically restart.

Now, click on OK then on Apply and then again on OK.

Reboot your computer now for the changes to take an effect.

Method 2:
Start your PC in safe mode in Windows 10

Boot the PC in safe mode and check if the PC shuts down. Refer the article to
Start your PC in safe mode in Windows 10
.

If the PC is not shutting down in safe mode then perform a clean boot from safe mode. Refer the article on
How to perform a clean boot in Windows.
If the PC is not shutting down then please refer the section How to determine what is causing the problem after you do a clean boot.

Note:
Clean Boot starts Windows with a minimal set of drivers and startup programs, so that you can determine whether a background program is interfering with your game or program. Also, you may not be able to use some programs in clean boot.

Note: Please refer the section
Reset the computer to start normally after clean boot troubleshooting
to boot the computer in to normal mode after troubleshooting.

You can also follow the suggestion from the article on how to
Improve PC performance in Windows 10

For issues where the
event ID 10016 logged in event viewer, you may follow the below suggestions and check if it helps.

Registry disclaimer: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the
registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs.

Please take a backup of the registry.
Follow the steps given in the link below:

How
to back up and restore the registry in Windows

• Open the
  Run dialog box by pressing the Windows key and the R key together
  
• Type
  Regedit and hit the Enter key.
  
• When the Registry Editor opens, navigate to the following location:
  

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Ole

• Delete the following keys from the right pane
  

DefaultAccessPermission

DefaultLaunchPermission

MachineAccessRestriction

MachineLaunchRestriction

• Restart your computer.
  

Deleting those four keys will cause DCOM to write default permissions for the system and should grant access to the apps requiring access to the DCOM Server.

For more information on event ID 10016 logged in event viewer, I suggest you refer to the article
DCOM event ID 10016 is logged in Windows

Hope it helps.

Regards,

Zaki