Windows 10: my pc only loads into bios i use as rock motherboard and i cleared my hard drive to see if...

i can’t load up windows it’s only putting me in bios

:)

 

Help with external hard drive

Hi Debbra,

Welcome to Microsoft Community.

I appreciate your interest in windows 10 and also for trying the troubleshooting steps to fix the issue. I understand the inconvenience you faced. I will certainly help you with this.

I would suggest you to plug in hard drive then check in disk management you can see the drive or not.

Follow the steps to check Drive in Disk Management.

• 
  Go to the Control Panel then click on the
  Administrative Tools. .
  
• 
  Under the Administrative Tool Click on Computer Management.
  
• 
  Click on Disk Management and check the External Hard Drive.
  

Also check in BIOS whether External Hard Drive is listed or not.

For help with the BIOS settings, refer to the computer manual or contact the manufacturer.

If it doesn’t work then, I would suggest you to update BIOS for updating BIOS contact Lenovo Support.

Follow the link:

http://support.lenovo.com/in/hi/

Disclaimer :

Modifying BIOS/complementary metal oxide semiconductor (CMOS) settings incorrectly can cause serious problems that may prevent your computer from booting properly. Microsoft cannot guarantee that any problems resulting from the configuring of BIOS/CMOS settings
can be solved. Modifications of the settings are at your own risk.

Hope this information is helpful. Please do let us know if you need further assistance, we’ll be glad to assist you.

Thanks.

 

Gigabyte motherboard, pc won't bootup after recent hard drive change

So I've previously had this problem when I added new SATA hard drives to an old one, all I had to do was switch hard disk priority to the one I wanted to boot from. But that's not working right now.

Error message: AMD Data Change...Update New Data to DMI!
Specs:

• Motherboard: Gigabyte ma785gmt-ud2h
• Four SATA hard drives, three 2tb and one 1tb
• One IDE hard drive, 160gb
• 6gb RAM
• Everything else is the default

What happened: I had an Amahi home server running on this PC with Ubuntu 12.04LTS as the OS. It was using the four SATA hard drives and everything was running smoothly. Then I read that it's easiest to have a setup where the OS/Amahi is installed on one small hard drive while the large hard drives are used to keep the files on, this makes it easy to update the OS without worrying about the files. So today I installed Ubuntu 12.04LTS on an old IDE 160gb hard drive that I had laying around, which would be perfect to use since there is exactly one IDE port on the motherboard.

I disconnected all hard drives, connected the IDE, installed Ubuntu, and rebooted. I got a "AMD Data Change...Update New Data to DMI!" message.

What I tried:

• Have the IDE be given priority over other hard drives.
• Connecting all the hard drives back, with and without the IDE hard drive. Same message.
• Disconnect all hard drives, connect IDE, and set BIO to opimised defaults. Same message.
• Disconnect CD drive with only IDE attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with only SATA attached, same message. Reconnect CD drive, same message.
• Disconnect CD drive with SATA and IDE attached, same message. Reconnect CD drive, same message.
• Just IDE connected, mess with the peripheral settings by changing "OnChip SATA Type" to ATHCI, RAID, or IDE. Tried this with "As SATA Type" and with "IDE" set for the port4/5 type
• Just IDE connected, disable SATA controller
• Disconnect IDE, reconnect original hard drives. I still get the same DMI message.
• Attempt to boot from the SATA hard drive that has Ubuntu on it, using each of the SATA ports.
• Update BIOS to F10B, disabling the "Remember DMI" option. I reconnected all hard drives and the CD drive (the pdf said the 'system' will redetect all devices). Now I got the "AMD Data Change...Update New Data to DMI! Update Success" message, still hanging there. Rebooted, now it's the original message.

So I am at a loss. Any suggestions?

Edit: there were many suggestions to try clear the CMOS, however that didn't seem to help the posters. I haven't tried that, but if people suggest I should then I will do so tomorrow.

 

Gigabyte motherboard, pc won't bootup after recent hard drive change

now it look like it freeze because its searching boot sector...leave it there see if you have keyboard. and try booting in menu with only 1 pre formated hd on anjy port.


Your bios also as some kind of dual bios design a think... may cause problem or not. when problem like that append on integrated RAID controller, reset your bios by unplugging PC remove side cover. press power see led coming on then of really fast, if no this good too, no power on motherboard, remove cr2032 battery, then put jumper in reset position like short pin 2,3. (check if it output 2.8 to 3.0 volts if under change it), put back cmos battery , now unshort cmos jumper back to original position. plug power . boot, ERRoR about bioa , configure raid and check