Windows 10: My Surface Pro X - Windows 10 Home can install canon printer drive

Anyone can help

My surface pro x - Win 10 Home can install canon printer driver Canon LBP7110Cw as other laptop can Win 10 Pro

using the following method


1 Add printer from Win 10 option - Detected printer , driver unavailable , this method

on a Win 10 Pro ok


2 Install driver from exe , 64bit , can't install , 32bit install halt way get error

" An Error occurred during the processing of printer LBPC7110Cw"



Any help will be appreciated


Thanks in advance


SB

:)

 

Canon PIXMA MX472 All-in-One - Scanner did not install

Like the previous poster suggested, unplug the USB cable from the printer and turn off the printer.
Start the installation of the drivers, watch the install windows VERY CAREFULLY as there will be instructions as to when you need to plug the USB cable into the printer and turn the printer on.
I ran into this exact scenario when I installed my printer after a Windows 10 Pro install (1909).
The printer ran fine but when I tried to use the scanner, no dice...
Printer is Canon MG6820.

The only other thing I can suggest if that doesn't work is to turn your firewall off, turn off any anti-virus software, and then do the driver installation again following the install windows VERY CAREFULLY.
I had to do that step on a Windows 7 Pro PC in order for the scanner to work.

EDIT: Follow this link to see where I asked for help: Solved: MG6820 can't scan from the Operation Panel... - Canon Community


Good Luck.

 

Canon Printer listed under Disk drives?


Just a question for you guys, in my device manager my canon printer is listed under Disk drives, USB connection??
Its also listed correctly under printers too. Should I remove it from being listed under disk drives?? or leave it alone?
Thanks guys.

 

Problem updating Windows Surface Pro 4 with Windows 10 feature updates

Hi,

I have manage to install image for Microsoft Surface Pro 4 by going to https://support.microsoft.com/en-us/...erecoveryimage and download a recovery image for Microsoft Surface Pro 4.

What I did to reset your Surface from a USB recovery drive was:
Step 1: Make sure your Surface is turned off and plugged in (hold down the power
button for 30 seconds).
Step 2: Insert the USB recovery drive into the USB port on your Surface.
Step 3: Press and hold the volume-down button while you press and release the
power button on your Surface.
Step 4: When the Surface logo appears, release the volume button.
Step 5: When prompted, select the language and keyboard layout you want.
Step 6: Select Troubleshoot > Reset your PC.
If prompted for a recovery key, select Skip this drive at the bottom of the
screen.
Step 7: Select the target operating system you wish to reset. This
refers to the current operating system installed on your Surface.
Step 8: Select Yes, repartition the drives, and on the next page, select Next.
Step 9: Choose Just remove my files.
Step 10: Select Reset.
Surface restarts and the Surface logo displays while the reset process continues
(this can take a while).

This always fails and I have to do the below which continues installation.
Windows 10 Installation Media:

1. Insert the Media (DVD/USB) in your PC and restart.
2. Boot from the media.
3. Select Repair Your Computer.

Select Troubleshoot.

1. Choose Command Prompt from the menu:

Type in the command:
Diskpart
Type in the command:
List disk (Note which disk is your Boot drive number mine is 0)
Type in the command:
Sel disk 0
Type in the command:
List vol (Note which volume is the EFI partition mine is 4)
Type in the command:
Sel vol 4
Type in the command:
assign letter=V:
Type in the command:
Exit
Type in the command:
V:
After you have assigned a drive letter Using Diskpart You can format the EFI partition:
Example: if you assigned a letter V to the partition the command would be:
format V: /FS:FAT32
Type in the command:
bcdboot C:\windows /s V: /f UEFI


Now I have an issue that I cannot install Feature Updates. They keep failing to install.
Any ideas how to resolve issue?