Windows 10: my wifi adapter causes blue screen as soon as it connects to wifi

I am using https://www.amazon.com.au/gp/product/B07YBS7C4R/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 this model. It's fine with my other wifi adapter, but this one causes blue screen.However, I manually downloaded RTL8811AU driver from realtek webpage. And it kinda works and not.Whenever I manually install the driver and reboot, there is no blue screen. Just good connection with no error.Then, when I reboot again or disconnect wifi and connect again, blue screen occurs again.Here is my dmp fileshttps://1drv.ms/u/s!AnB4Q2rhjkAMaYRihws_jNgUGlM?e=JLeTPw

:)

 

WiFi Adapter Causing Blue Screens in Windows 10

So basically, a little while ago I asked a question that my computer keeps on blue screening. I ended up fixing the problem by uninstalling my graphics driver, but I installed it back because it created a few problems. Now I have blue screens whenever I
move my computer or just randomly at random times when I'm using it. However, I used BlueScreenView (third-party software) to see what was causing my blue screens. I found out that my network adapter was causing the problem. The Blue Screen stopcode was 0x000001d3
and it said it was caused by the driver Qcamain10x64.sys which it said was my WiFi adapter. So I disabled it and booted up my computer and everything worked fine, no blue screen no problems, except one MAJOR problem, I had no WiFi Connection. So I re-enabled
my network adapter and the blue screens came back. Can somebody please suggest a way I can deal with that driver (e.g. installing another driver) and solve my blue screens? I would appreciate it a lot!

Computer Info:

• Asus TP200SA
• Intel Celeron N3050 Dual-Core (2.16GHz)
• Intel HD Graphics
• 4GB RAM
• 64GB Storage
• Running Windows Version 10240

 

USB Wireless adapter not connecting to Wifi

Hello

I am having trouble making my new USB Wifi Adapter to work. The drivers are working fine but the issue is it is not connecting to wifi.

1. I am using Windows 10
2. The adapter which I am trying to work is Alfa AWUS036NHA 150Mbps
3. I have also one USB mini wifi adapter attached to my other USB through which I am currently using internet

From the above screenshot, the Wi-Fi 2 is which I am trying to connect. When I right-click on Wi-Fi 2 and click on Connect/Disconnect, It shows the already connected Wifi through USB mini adapter.

When I Disable WiFi and try to connect through WiFi 2 then it shows an error "Change settings, such as making a connection metered"

The device utility does not show any Wifi available connections though there are 2-3 wifi connection is there.








any idea how can I make connect to internet using my new Alfa AWUS036NHA 150Mbps Wireless USB Adaptor - Wi Fi 2 on Windows 10 ?

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?