Windows 10: Need to 'Net stop' and then 'Net Start' repeatedly each time I reboot

I have windows 10 Home Edition.
I have a Synology DS212 as a NAS box.

Until recently it worked faultlessly. But, in the last couple of weeks, accessing the NAS box has been all but impossible. Each time I try to access any of the data on it, it brings up a 'box' Network Credentials? saying that my Password is 'wrong' and I can't have access to the drive

However, if I:-

Cmd>
Run as Administrator>
net stop workstation /y
net start workstation

..... the system WILL accept the password tried previously which had just failed.... and the system then works..... until I boot down and re-boot up..... when I will be forced to use Net Stop etc. again to regain access to my data.

What am I doing wrong? The password and user name ARE correct despite what the message says because they work as expected after Net Stop etc..


There are some suggestions on the web that I should address this via NTLM...... but, apparently W10 Home does not give such access to NTLM. There are suggestions that I can 'add on' those controls similar to W10 Professional..... but it requires a complex CMD to download the 'program'.... but the correct 'command' seems to be dependent on which version of Windows I am running..... but there are no clues as to how I get the correct version of the software.

Any thoughts on solving this problem? It's driving me NUTS!

I have tried all the options that I can imagine... eg following these instructions:-

[COLOR=rgba76, 88, 97, 1] [/COLOR]https://www.lifewire.com/how-to-reset-network-settings-in-windows-10-4684679

Performing the following

[COLOR=rgba76, 88, 97, 1]

• Type netsh winsock reset and press Enter.
• Type netsh int ip reset and press Enter.
• Type ipconfig /release and press Enter.
• Type ipconfig /renew and press Enter.
• Type ipconfig /flushdns and press Enter.

[/COLOR]

[COLOR=rgba76, 88, 97, 1]3. Restart computer.[/COLOR]

[COLOR=rgba76, 88, 97, 1]..... all to no avail, so far. The only thing that works is Net Stop, Net Start! But that's only temporary.[/COLOR]

Ian

:)

 

Microsoft .NET Framework, Unhandled exception

Hi,

Welcome to Microsoft Community.

I suggest you to un-check and recheck .Net framework 3.5 and .Net framework 4.6 advance series from Windows features.

Try the following steps:

• Press Windows + R keys to open Run command.
• Type Appwiz.cpl and select "turn Windows feature on or off" from the left
• Uncheck .Net framework 3.5 and .Net framework 4.6 advance series.
• Restart the computer
• Repeat step 1 and 2 and check .Net framework 3.5 and .Net framework 4.6 advance series.
• Restart the computer.

Regards,

 

Command: net stop wuauserv says service is starting or stopping

Hi ! I had some issues with windows update so I looked up some solutions and the one with running commands in cmd is only one but when I run the command: net stop wuauserv , it says the service is starting or stopping and same case is with command : net
start wuauserv.

I have also tried the troubleshooter and trying to start the service from the list of services but the start stop are disabled and it shows as Stopping.

Please Help !

 

.Net Native Framework Package 1.0 and VCLibs 12 updating numerous times daily

Hi Graham,

Thank you updating on the status.

To assist you better, I would like to ask what is the exact error message and error code.

Also, I suggest you to manually reset Windows Update Components by following the steps below:

1. Press Windows key + X and click on Command Prompt (Admin).

2. Stop the BITS, Cryptographic, MSI Installer and the Windows Update Services. To do this, type the following commands at a command prompt. Press the “ENTER” key after you type each command.

• net stop wuauserv
• net stop cryptSvc
• net stop bits
• net stop msiserver

3. Now rename the SoftwareDistribution and Catroot2 folder. You can do this by typing the following commands in the Command Prompt. Press the “ENTER” key after you type each command:

• ren C:\Windows\SoftwareDistribution SoftwareDistribution.old
• ren C:\Windows\System32\catroot2 Catroot2.old

Note: Do not rename the Catroot folder, you need to rename
only the Catroot2 folder

4. Now, restart the BITS, Cryptographic, MSI Installer and the Windows Update Services. Type the following commands in the Command Prompt. Press the “ENTER” key after you type each command.

• net start wuauserv
• net start cryptSvc
• net start bits
  
  net start msiserver

5. Close command prompt and check for updates again.

Please revert with necessary information and we'll be glad to assist you.