Windows 10: NETSH.EXE

I have started to get the problem on a Lenovo Yoga Laptop discussed in this link. https://www.windows10forums.com/threads/system32-netsh-exe-why-is-it-popping-up.23596/ I have run Malware & Window Defender scans. It is not causing a problem but just an irritant and annoying! Just wondered if anyone has a solution.Ron

:)

 

How to reset whole netsh? (Windows 7)

Was wondering has the commands changed somehow since on Windows XP and on Windows Vista 'NETSH INT RESET ALL' cleaned entire netsh up from top to bottom.

Now on Windows 7 this same command says no go and only way I can see it is by building .cmd/.bat which does something like:

Code: netsh winsock reset all netsh int 6to4 reset all netsh int ipv4 reset all netsh int ipv6 reset all netsh int httpstunnel reset all netsh int isatap reset all netsh int portproxy reset all netsh int tcp reset all netsh int teredo reset all[/quote] now the king of the hill of bugs is this doesn't actually do even it's job even after reboot. values setup to are not reset to defaults. (I know I could add more entire list of entries there is, but looking for clean delete/wipe settings & default everything not to dump entire list of resets.)

So, anyone got a plan B?

 

router logs DoS attack from a local PC....

Well you did not say that you don't really know what you are doing. It's not a problem of course, but it changes things a little.

It's not even clear if the PC or the router is the problem at this time, so I suggested that you disable some unnecessary things which are usually known to cause many problems, sorry if those were too complicated.

• You could reset some network related stuffz on the PC as a next step. Open an elevated command prompt (run as administrator), and enter the followings on the PC:
  netsh int ip reset reset.log
  netsh int ipv6 reset
  netsh winsock reset
  netsh branchcache reset
  netsh advfirewall reset
  (note: You can export your current firewall rules in the "group policy" before the reset if it's needed for some reason)
  
  
• Btw, Would it be a problem to reset the router to the default settings if the things we are trying will not help? There is a menu point for that called "factory settings" (and also a little hole on the back if you prefer that one).. the Administrator username in the router after the reset would be admin and the password is probably on a sticker at the bottom of the router (special settings needed to go online with your ISP might be also necessary)
  This is not needed now (not yet), but perhaps the source of the problem is at the router and not the PC in question, so we may come to that eventually.

ps.: Do you have a second network card you could test in that PC and a different cable to rule out some hardware issues on the PC side?

 

Cortana Won't Connect

Hi,

To better assist you, what are the troubleshooting steps have you done so far? Have you tried
resetting and re-configuring
your
TCP/IP Settings? If not, we suggest that you do so. Kindly perform these
methods of troubleshooting and check if Cortana can connect to the internet after performing these methods:

Method 1: Reset TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  this command:
  
  • 
    netsh int ip reset
    and hit
    Enter.
    

Exit
Command Prompt
and
monitor your Network Connection.

Method 2:
Reconfigure TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  these following commands:
  
  • 
    netsh int tcp set heuristics
    disabled
    
  • 
    netsh int tcp
    set global autotuninglevel=disabled
    
  • 
    netsh int tcp set global
    rss=enabled
    

Update us on how it goes.

Regards.